1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with special edge lip to hug bright work when clamped down. Shape outline to suit.
Body Hole Plug
p/n: 20-0843-20
Plug, style-side bed side panel. One and five eighths (1-5/8) inch diameter. Fits 1-1/16" hole.
Door Bumper
p/n: 70-2045-71
This Door to Body Bumper is quality reproduction of the original factory part. Use varies depending upon model and body type. Some models uses four (4) bumpers for front doors and four (4) for rear doors.
Tailgate Side Seals
p/n: 70-4009-85
This Tailgate Side Seals includes right and left side with installation screws. These seals are properly molded from originals for a factory like fit.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
PCV valve grommet
p/n: 20-2696-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2723-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Made from flat foam rubber to provide protection.
Hood to Fender Bumper
p/n: 70-1962-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) required per car.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Parking Brake Cable To Floor Seal
p/n: 20-0853-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment and seal. This works to seal the parking brake cable as it passes through the truck floor pan.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Tailgate Bumper
p/n: 20-0888-45
These Tailgate Bumpers are designed from original parts for a correct fit. Sold as a pair.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
2" Firewall Grommet
p/n: 60-0707-20
This Firewall Grommet is used to run the body wiring harness at the engine bulkhead through the firewall. Special design for this usage.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Bumper Cap - Door, Hood and Trunk
p/n: 82-0020-42
This Bumper Cap is a quality reproduction of the original factory part. Serves as a Door, Hood and Trunk Bumper Cap for adjustment bolt. 7/8" diameter X 7/16" thick. Each
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Hood Bumper
p/n: 70-0991-42
Bumper, hood to fender ledge. Typically four (4) to six (6) used per car.Length: 1.15625 inches. Width: .3125 inches.
Tailgate Bumper
p/n: 70-1609-87
This Tailgate Bumper is a quality reproduction of the original factory part. Made of a high-quality EPDM rubber, the bumper attaches to the vehicle body to support / cushion the tailgate closure.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Gearshift Seal
p/n: 20-2875-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.