Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Front Door Weatherstrip
p/n: 82-0074-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Front Engine Mount
p/n: 60-0462-11
This front Engine Mount is a new replacement mount manufactured to meet or exceed factory specifications. For six (6) cylinder models only.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Hinge Pillar Weatherstrip
p/n: 82-0073-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hood To Cowl Weatherstrip
p/n: 82-0067-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood To Fender Bumper
p/n: 70-1836-42
This Hood To Fender Bumper is designed from the original part for superior fitment, finish and function. This bumper is manufactured with quality EPDM dense rubber and measures 1-7/16" x 11/16" inches.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
License Plate Light Lens Gasket
p/n: 70-3497-17
This License Plate Light Lens Gasket is designed from the original part for superior fitment and seal. This gasket fits between license plate light lens and housing.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Parking Brake Pedal Pad
p/n: 70-4804-22
This reproduction Parking Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace a worn or damaged original pedal pad.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0774-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Radiator Mounting Insulator Pads
p/n: 70-2238-31
A four (4) piece set of Radiator Mounting Insulator Pads. For use on all four corners of the radiator. For vehicle models with three (3) wide core radiators.
Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0344-80
This Side Window Vertical Leading Edge Weatherstrips pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Splash Apron / A-Arm Dust Shield
p/n: 70-3335-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Taillight Housing to Body Seals
p/n: 70-3488-15
This Taillight Housing to Body Seal pair is designed from the original part for superior fitment and seal. These reproduction seals fits between the taillight housing and the vehicle body.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Trunk Weatherstrip
p/n: 70-0774-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
U Jamb Lock Pillar Filler
p/n: 82-0064-79
This U Jamb Lock Pillar Filler seals the bottom of the rear side window, and may also be known as a door jamb seal.
Vent Window Weatherstrip Set
p/n: 70-4074-55
This four (4) piece Vent Window Weatherstrip Set is for both driver and passenger doors of GM A-Body 2 door models. All of the pieces were designed from original parts for a precise, factory like fit.
Window Felt Beltline Weatherstrips
p/n: 80-0389-57
This is a Standard material style replacement side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece set includes the inner and outer felt beltline weatherstrips for each side and quarter window.