This two (2) piece Vent Window Weatherstrip Set (pair) fits both driver and passenger doors of the vent window assemblies.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Contains plastic pins that are attached to the door weatherstrips and molded ends with metal cores. Also contains ten (10) plastic clips for the molded ends.
This two (2) piece Division Bar Glass Run Channel pair installs between the front of door glass and the back of the vent window.
This Hardtop Roof Rail Weatherstrip pair is made of high-quality EPDM rubber with fully molded ends and metal cores for a factory like fit. These seals fit on the roof of the vehicle and work to seal the side windows when the window is fully raised.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Gaskets, taillight lens to housing.
Side window vertical leading edge weatherstrip.
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Bumper, front suspension lower arm.
This Splash Apron pair is designed from the original part for superior fitment and seal. Used to seal the front fender apron to frame lower rear.
This Quarter Window U Jamb Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.. Fully molded authentic rubber construction with metal core.
This Voltage Regulator Cover Shield is designed from the original part for superior fitment and function. This cover shield is located over and above the voltage regulator.
Seals, cowl side panel to fender. Includes fasteners.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction using the correct profile dense rubber extrusion.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Mount, rear engine support on transmission.
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
This Gravel / Stone End Shield rubber is designed from the original part for superior fitment and usage. One (1) pair per car. This part fits between the vehicle body and rear bumper. For all except Wagons.
This Air Deflector piece is designed from the original part for superior fitment and seal. Piece is die cut from quality masticated rubber to authentic original dimensions. This piece fits at the bottom of radiator core support to frame. Used on V8 models.
Seal, top of radiator support to hood air deflector.
Seal, radiator support to bottom of radiator. "L" shaped. Twenty six and three eighths (26-3/8) inches long.
Seal, radiator side air deflector. Seventeen and seven sixty fourths (17-7/64) inch by two and seven eighths (2-7/8) inch.
Pad, radiator mounting. Lower.
Pad, parking brake pedal.
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Seal, front fender extension to fender.
Pad, radiator mounting insulator.
Pad, radiator mounting insulator.
Gaskets, parking light lens.
Bumper, hood on fender. Push-in type three fourths (3/4) inch wide. Four (4) piece set.
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Seals, headlight opening cover plate. With headlight covers.
Seal, radiator side air deflector. Three (3) inch by fourteen and one eighth (14-1/8) inch.
Insulator, front coil spring.
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Bumper, ash tray door.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Pad, trunk lock cylinder sleeve. Four (4) lug cylinder type.
Bumper, door. Installs on back edge of door. Please check your car for quantities required.Usually two (2) to eight (8) per vehicle.
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.