Rear stationary quarter window weatherstrip.
These front door vent window seals are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and contain metal cores with attaching tabs that run vertically on the division post.
This tailgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the tailgate opening, directly to the body, with properly spaced plastic clips. Includes molded ends that contain brass cores.
Leaf Spring Shackle Bushing Kit - For rear of rear leaf spring. Complete with shackle bars and bolt assembly with rubber bushings. Two (2) kits required per car.
Front Coil Spring Saddle Insulator Kit - Two front coil spring bushings and two spring insulators to restore the performance of your classic vehicle. Requires two (2) per car.
Seal, rear bumper to body.
Weatherstrip, outer beltline. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Front motor mount support. Right-hand side only. Fairlane big block engines. See description for fitment.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Front motor mount support. Left-hand side only. Fairlane big block engines. See description for fitment.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Seal, top of radiator to hood.
Seal, steering column to floor.
Seal, radiator grille opening. Cut to fit.
Seal, hood to cowl. Includes fasteners imbedded in place as original.
Gaskets, taillight to body.
Valves, rear floor pan extension drain.
Channel, door window glass lower rubber. Front or rear doors. One (1) pair does two (2) windows.
Rear Leaf Spring Bushing - Original style leaf spring bushings used in front eyes of rear leaf springs. Requires two (2) spring bushings per vehicle.
Pad, brake pedal. Models with manual transmission and manual brakes.
Pad, brake pedal. Models with automatic transmission and manual brakes.
Insulator, gear shift.
Rear Leaf Spring Insulator Pad - An exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Gaskets, air vent inlet duct to cowl.
Gaskets, taillight lens.
Repair kit, stabilizer bar end. Eleven (11) piece set. Two (2) kits required per car. Hex head bolt. 3/8"-16nc x 6-7/8" lg. Comes with metal sleeve, four (4) cup washers and four (4) rubber grommets.
Gaskets, back-up light lens.
Seal, accelerator pedal rod.
Insulator, front coil spring upper.
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Plugs, quarter panel drain.
Gaskets, parking light lens.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Bumper, brake and clutch pedal arm.
Bumper, door. Installs on back edge of door. Please check your car for quantities required.Usually two (2) to eight (8) per vehicle.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.
Tip, sun visor arm boot. Used where sun visor hooks to clip in center. Two (2) required per car.