Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Inner Fender Splash / Dust Shield Set
p/n: 70-4669-45
This four (4) piece Inner Fender Splash / Dust Shield Set is designed from the original part for superior fitment and seal. Inner Fender pieces are die-cut from quality masticated rubber to authentic original dimensions. These pieces fit to the inner front fenders.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Kick Panel Hole Cover
p/n: 70-4536-45
This Kick Panel Hole Cover is designed from the original part for superior fitment and function. Cover is made from high-quality EPDM 80 durometer dense rubber to provide excellent durability and service.
Side Marker Light Gaskets
p/n: 70-4335-17
This Side Marker Light Gasket set is designed as a premium upgrade over the original part for superior fitment and a highly finished look. Fully molded gaskets installs between the side marker and body when not using a chrome bezel.
Quarter Post To Window Seals
p/n: 70-4766-79
This Quarter Post To Door Window seal pair is designed from the original part for superior fitment and sealing. These seals are located on the quarter post to window.
Front Bow Weatherstrip
p/n: 20-2798-64
This Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Hood to Cowl Firewall Weatherstrip
p/n: 20-2752-42
This Hood to Cowl Firewall Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts with the included clips at the rear of the engine bay firewall directly to the body.
Quarter Panel Drain Valves
p/n: 20-2770-45
These Quarter Panel Drain Valves are constructed of a durable rubber and are a direct-fit replacement. This product is sold as a pair.
Rear Leaf Spring Insulator
p/n: 20-2733-32
This Rear Leaf Spring Insulator is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Upper Control Arm Bumper
p/n: 20-2727-32
This Upper Control Arm Bumper is designed from the original part for superior fitment and function. A molded rubber bumper which serves as a bump stop for the front suspension.
Firewall to Hood Weatherstrip
p/n: 70-3465-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile made in sponge rubber. This weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Turn signal light gasket
p/n: 20-0749-16
Gaskets, side marker light. Front and rear. Four (4) piece set.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Rear Spoiler Mounting Gaskets
p/n: 20-2872-87
This Rear Spoiler Mounting Gasket pair is designed from the original part for superior fitment and seal. These gasket fit between the rear spoiler mounting pedestals and the trunk decklid.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Hood to Cowl Weatherstrip
p/n: 70-2807-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Parking Brake Cable To Floor Seal
p/n: 20-0760-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment, finish and function. The part protects the parking brake cable as it passes through the truck body floor pan.
Trunk Decklid Bumper Stop
p/n: 82-0160-87
This Trunk-Decklid Bumper Stop is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Air Cleaner Lid Gasket
p/n: 20-2701-20
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for Six (6) Cylinder engine models.
Door Glass Run Channel
p/n: 70-4313-58
This Door Glass Run Channel is designed from the original part for superior fitment and seal. The window glass run channel presses into the door channel at the top and back part of the door. This single piece fits either the driver (LH) OR the passenger (RH) side front door.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 70-4014-42
This Firewall To Hood Weatherstrip - Cowl Lacing comes with pre-drilled mounting holes and mounting clips installed. Made of high-quality EPDM rubber and to the original design for a factory like fit and appearance.
Axle Rebound Pad
p/n: 20-2730-32
Bumpers, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
Air Cleaner Lid Gasket
p/n: 20-2700-20
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for 302, 351 and 390 V8 engine models.
F-100 Brake Pedal Pad, Automatic
p/n: 70-4485-22
This reproduction F-100 Brake Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
Side Window Glass Run Channel
p/n: 20-0812-58
This Side Window Glass Run Channel is designed from the original part for superior fitment and seal. Single length of flexible window run channel for the sides and top of door windows. For Left or Right side, order two (2) per truck as needed.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
Taillight Lens Gasket
p/n: 20-0746-15
Gaskets, taillight lens. Rectangular type. Style-side pickups before Serial # T00,001.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Taillight Lens Gasket
p/n: 20-0747-15
Gaskets, taillight lens. Square type. Useage: 1967-72: F100-350 Trucks EXCEPT Style-side 1973-77: F100-250 series Flare-side pickups before Serial #020,000.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
2-7/16" Floor Plug
p/n: 35-3508-45
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to ten (10) used per vehicle.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.