Gearshift Knob
p/n: 20-0763-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Brake and Clutch Pedal Bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Gearshift Floorplate
p/n: 20-0464-88
Seals, transmission cover to floor. Cork and rubber. Three (3) piece set.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Brake and clutch shank seal
p/n: 20-0758-23
Seal, clutch rod to floor. Useage: 1971-72: F100-350 series AFTER Serial #M00,001 1973-79: F100-350 series trucks
Gearshift Boot
p/n: 30-0412-24
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Brake and clutch shank seal
p/n: 70-0192-23
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Clutch Release Lever Boot
p/n: 20-0761-24
This Clutch Release Lever Boot is designed from the original part for superior fitment and seal. This boot is for the clutch release lever to clutch housing.
Brake Cable Boot
p/n: 60-0155-24
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Brown gearshift boot
p/n: 30-0129-89
Boot for column gearshift, short type. Brown rubber. For black see our #30-0129-24. All series with column shift.Color:brown Length: 1.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Brake Cable Boot
p/n: 60-0156-24
Boot, front brake cable end at brake backing plate. Two and seven eighths (2-7/8) inches long.Length: 2.875 inches.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Gearshift Boot
p/n: 20-2878-88
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Brake and clutch shank seal
p/n: 25-0051-24
Seals, brake and clutch pedal shank-to-toe board, sponge rubber. Two (2) per car.
Vacuum Clutch Cylinder Boot
p/n: 40-0084-24
Boot, automatic clutch vacuum cylinder rod.Length: 4.0 inches.
Brown Gearshift Boot
p/n: 40-0111-89
Boot, base of gearshift lever. Brown rubber. For black see our #40-0111-88. Made separately to fit most of our gearshift floorplates. Copied from original.
Parking Brake Boot
p/n: 60-0145-24
This Parking Brake Boot is used for the brake lever at the floor. Designed from an original part and molded from EPDM dense rubber for durability and proper fit.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Handbrake Pull Rubber Grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Steering Column Grommet
p/n: 40-0421-36
Grommet, steering column and transmission shift rod through firewall.Length: 4.375 inches.
Steering Column Grommet
p/n: 12-0012-36
Grommet, steering column and shifter at toe board, reproduced with all original details.
Clutch Lever Dust Boot
p/n: 20-2712-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. Made from Original Ford tooling.
Brake and clutch shank seal
p/n: 20-0634-24
Seal, clutch rod to floor. Used on motor side. Pre-molded with metal insert.
Gearshift Boot
p/n: 20-2877-88
Boot, 3-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Clutch and Brake Arm Seals
p/n: 20-2453-23
These Clutch and Brake Arm Seals are designed from the original part for superior fitment and sealing. A perfect reproduction of the seal pair with a steel metal core.
Gearshift Boot
p/n: 18-0017-88
Boot only, gearshift at floor, to replace boot section at original gearshift floorplate.Width: 4.50 inches.
Brake and Clutch Floor Plate
p/n: 18-0014-24
This Brake and Clutch Floor Plate is designed from the original part for superior fitment and seal. Fully molded in quality Black EPDM rubber. For Brown rubber see our #18-0014-89. Length: 7-1/2" inches.