Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Door Bumper
p/n: 40-0316-70
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Door Bumper
p/n: 34-0342-71
Door bumper, round, rubber with steel insert, (called door anti-rattle). Two (2) per door on all closed body styles, one (1) per door on convertible Sedan.
Rear Door Bumpers
p/n: 70-2365-71
This Rear Door Bumper pair is made from high-quality EPDM dense rubber to provide excellent durability. Fits at the rear door opening. Proper configuration with slots for retaining screws as original.
Bumper - LH Back Door
p/n: 60-0333-71
A molded rubber Left-Hand Back Door Bumper. Dovetail to be used with old castings.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Door Bumper
p/n: 30-0429-71
Bumper, rear door. Two (2) used per car. Correct design with proper clearance for screw hole.Width: 1.0 inches. Height: 1.0 inches.
Door Lock Bumper
p/n: 70-0538-71
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Door Bumper
p/n: 60-0581-71
Pad, door jamb. (Door side bumper). Two screw type with metal reinforcing inserts.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 10-0126-71
Pad, door jamb. One (1) required per door. Made to fit old door pad core.
Rear Hatch Door Bumpers
p/n: 70-4731-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Door Bumper Pad
p/n: 30-0032-71
This circular shaped Door Bumper Pad is designed from the original part for an authentic fit, finish, and appearance.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper
p/n: 70-2292-70
Steele Rubber Products has the best quality door bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.