Antenna Mount Pad
p/n: 60-0338-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Antenna Mount Pad
p/n: 60-0631-21
This reproduction Antenna Mount Pad is designed from the original part for an authentic fit, finish and appearance. For manually operated antennas.
Starter Button Cover
p/n: 60-0358-21
Cover, starter rod button, round slip over type. One and seven sixteenths (1-7/16) inch outside diameter. Good copy with bow tie center.
Antenna Mount Pad
p/n: 20-2936-19
This reproduction Rear Mount Antenna Pad is designed from the original part for an authentic fit, finish and appearance.
Antenna grommet
p/n: 70-1865-19
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Antenna Mount Pad
p/n: 50-0168-21
Pad, antenna mounting over windshield, one and thirteen sixteenths (1-13/16) inch outside diameter, one and one fourth (1-1/4) inch inside diameter.
Antenna Mount Pad
p/n: 30-0502-21
Pad, antenna mounting on fender. For fender mounted antennas only.
Horn Button Contact Cushion
p/n: 18-0027-21
Cushions, horn contact plate.Qty Required:3 Width: 1.0 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Starter Solenoid Boot
p/n: 60-0567-21
This Starter Solenoid Boot is designed from the original part for superior fitment and seal. The boot protects the solenoid plunger starter switch at the starter, shielding it from dirt, moisture, and other contaminants that could affect performance of the starter motor.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Antenna Mount Pad
p/n: 60-0050-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Battery Cable Grommet
p/n: 40-0333-21
Grommet, battery hot cable through frame. Three fourths (3/4) inch inside diameter for one and three sixteenths (1-3/16) inch hole through frame.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Battery Cable Boot
p/n: 30-0374-21
This reproduction Battery Cable Boot is designed from the original part for an authentic fit, finish and appearance. Boot is for the battery cable at starter solenoid.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Generator Outer Splash Shield
p/n: 20-1035-21
This Generator Outer Splash Shield is designed from the original part for superior fitment and seal. Includes attaching staples.
Horn Ring Pressure Rubber Pad
p/n: 20-1036-21
This Horn Ring Pressure Rubber Pad is designed from the original part for superior fitment and function.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Antenna Lead Wire Grommet
p/n: 20-1807-19
This fully molded rubber Antenna Lead Wire Grommet is designed from the original part for superior fitment and function. Works to seal front mount antenna lead wire to the vehicle body.
Horn Bell To Bracket Grommets
p/n: 20-1562-21
This reproduction Horn Bell To Bracket Grommet pair is designed from the original part for an authentic fit, finish and appearance. Replace worn and deteriorated original grommets with this direct fit like OEM reproduction.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
Insulator Pad
p/n: 30-0404-48
This Insulator Pad is designed from the original part for superior fitment and function. This dense rubber insulator is used on various places on the vehicle. Replaces factory #232856 and #324851.
9/16" Battery Strap Grommet
p/n: 32-0491-21
This Battery Strap Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the battery retaining hold-down bolt.
1" Firewall Grommet
p/n: 32-0320-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the wiring through the front body brace, right and left.
1/2" Wiring Grommet
p/n: 32-0161-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment. This grommet is made from quality dense rubber to provide excellent durability. Designed for the spark plug wire organizer bracket.
1-1/8" Antenna Hole Plug
p/n: 35-0327-45
This Antenna Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for antenna mounting for inner fender at shroud, vehicles without a fender-mounted antenna.
1" Antenna Grommets
p/n: 32-0390-21
This Antenna Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
7/8" Wiring Grommet
p/n: 32-0002-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
11/16" Wiring Grommet
p/n: 32-0003-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
31/32" Firewall Grommet
p/n: 32-0133-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed with wide spacing to pass electrical wiring and cables through metal frame.
Antenna Mount Gasket
p/n: 70-5054-19
This Antenna Mount Gasket is a high-quality reproduction of the original factory part. This mounting gasket installs between the antenna mounting base and fender to protect the painted surface.