Front Spring Bumper
p/n: 70-0172-32
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Front Suspension Bumper
p/n: 40-0250-32
Bumper, front suspension, lower arm. Two (2) per car.Width: 3.0 inches. Height: 1.625 inches.
Axle Rebound Pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Front Spring Bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Axle Rebound Pad Service
p/n: 10-0003-35
Pad, rear axle rebound, perfect duplication. Length: 4.0 inches. Height: 1.25 inches.
Axle Rebound Pad Service
p/n: 70-0502-32
Bumper, rear spring to frame, two (2) per car.Width: 2.5 inches. Height: 2.5 inches.
Axle Rebound Pad
p/n: 70-0238-32
Pads, axle rebound, rear two and one fourth (2-1/4) inches diameter by three (3) inches high.Height: 3.0 inches.
Axle Rebound Pad
p/n: 10-0002-35
Pad, front axle rebound, including bolt hole. Excellent copy, highest grade material.Width: 2.25 inches. Height: 1.50 inches.
Front Suspension Bumper
p/n: 27-0080-32
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
Front Spring Bumpers
p/n: 30-0087-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Front Suspension Bumper
p/n: 70-1022-32
Bumper, front suspension, lower on spring seat. Made with long lasting Buna rubber.1958: Also used on other models with air suspension.Width: 1.875 inches.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Ride regulator control grommet
p/n: 70-0639-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car. Made without rod hole. You cut rod slot as required at installation.
Front Spring Bumpers
p/n: 30-0120-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Axle Rebound Pad
p/n: 27-0081-32
Bumper, rear axle on leaf spring.Width: 3.25 inches. Height: 4.75 inches.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Radius Arm Bushing Set
p/n: 20-0780-32
This Radius Arm Bushing Set is a quality reproduction of the original factory part(s). This eight (8) piece includes four (4) each D6TZ-3B203-A Front Axle Bushings and four (4) each C6TZ-3B203-C Frame End Bushings. Fits four-wheel (4WD) drive trucks.
Axle Rebound Pad
p/n: 50-0051-35
Pad, axle rebound, ring type, usually retained by leather straps or clip & bolt.