Door Bumper Stops
Pad, door jamb edge. With metal insert as original.Length: 1.1875 inches. Width: 1.5625 inches.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Bumper, door.Chrysler 1934 Bumper, door. Chrysler 1932-34 Bumper, decklid. Two (2) required per car. Length: 2.50 inches. Width: 1.8125 inches.
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Bumpers, rear door upper, right and left.
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Pad, door jamb. Closely copied from original.Width: 2.0 inches.
Bumpers, top of rear of door.
Cushion, door wedge plate, right and left, for door aligning lug receiver.Width: 1.1875 inches. Height: .625 inches.
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Wedge pads, door aligning. Up to four (4) pair required per car.
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Bumpers, door. Installed on rear of door just above lock.
This door bumper is designed from the original part and attaches to door with single screw. Four (4) required per vehicle.
Wedge cushion, door dovetail. This is the rubber block which goes behind the dovetail receiving bumper or shoe.
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Bumper, door, rubber, round style, screw retained. One and five sixteenths (1-5/16) inch diameter.
Bumper, door side. Approximate size one half (1/2) inch by three fourth (3/4) inch by two (2) inch.Length: 2.0 inches. Width: .50 inches. Height: .
Bumper, door edge. One (1) required per door.Width: 1.5625 inches.
Bumper, door side.Width: 1.0 inches. Height: .9375 inches.
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Bumper, door, lower, held by one (1) screw and one (1) carrot retainer.Length: 1.125 inches. Width: .625 inches.
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Bumper, door, rubber only. Atwood style.
Bumper, door side, upper. Oblong type, perfect copy of original.Length: 2.4375 inches.
Bumper, oblong, door side. An auxiliary door jamb or side bumper.Width: 1.75 inches. Height: .75 inches.
Bumper, door side, slotted block type. Used two (2) per golf door and four (4) to eight (8) per car on open model doors.Width: .875 inches. Height: .
Kit, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Bumpers, rear door opening. Proper configuration with slots for retaining screws like original.
Bumper, dovetail, left hand back door, rubber only. To be used with old casing.
Door jamb pad (door side bumper). Round, with steel core, screw held.
Bumper, rear door. Two (2) used per car. Correct design with proper clearance for screw hole.Width: 1.0 inches. Height: 1.0 inches.
Pad, door jamb. Earlier type, screw retained, perfect copy.Length: 1.50 inches. Width: 1.25 inches.
Bumpers, lower door. Slip over screw head type.
Pad, door jamb. (Door side bumper). Two screw type with metal reinforcing inserts.
Pad, door jamb.Length: 1.50 inches. Width: 1.25 inches.
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Pad, door jamb. One (1) required per door. Made to fit old door pad core.
Pad, for door. Circular shape, one and one fourth (1-1/4) inch diameter.
Bumper, door side.Length: 1.4375 inches. Width: .6875 inches.
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Bumper, door check link arm. Fully molded with proper cross section and design.
Pad, door jamb, used frequently for open and closed cars.
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Bumper, door side on hinge post.
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Bumper, on lower door and/or fuel filler cover. Type with threaded end.
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers, door. Five eighths (5/8) inch high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers, door. Installed on rear of door by lock.
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Pad, door side bumper. Clip retained. Appears identical to Atwood #107, #208.Width: 1.5 inches. Height: 1.3125 inches.
Pad, door jamb (door side bumper). Length: 1-1/4" inches. Width: 15/16" inches.
Pad, door side bumper. Clip retained.
Pad, door jamb (door side bumper).Length: 1.1875 inches.
Bumper, rear door bottom.
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface. Length: 1.0 inches.
Wedge pad, door aligning dovetail. Goes under bumper retainer.Length: .9375 inches. Width: .9375 inches. Height: .4375 inches.
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Pads, door striker plate.
Bumper, door.Length: 1.0 inches. Height: .4375 inches.
Pad, door jamb. Usually requires two (2) per door.Length: 1.0 inches. Width: 1.0 inches. Height: .50 inches.
Bumper, door side. Four (4) used per car. Not a generic substitute, but manufactured just like the factory original.
Bumper, door jam.
Bumpers, upper door. Closed cars.
Bumper, door, used upper and/or lower as required. Excellent detail using highest quality rubber.Length: .875 inches. Width: .8125 inches. Height: 1.
Front door glass up stop bumper. For models w/out power vent windows. Use two (2) or four (4) per vehicle. Refer to your vehicle to see how many are required.
Bumper, rear door. Plug style. Compare with your original, use as required.
Bumper, door, bottom
Bumper, door, rear of door
Support, door garnish molding. Up to twenty (20) required per car.Width: .875 inches. Height: 1.0 inches.
Bumper, door. Requires two (2) per door - one (1) upper on door and one (1) lower on door.
Bumper, rear door lower.Length: 1.0 inches.
Bumper, front door pillar, upper and lower.
Bumper, door upper center post.
Bumpers, door jam. Two (2) required per door.
Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Bumper, door upper. Molded with carrot retainers like original.Length: 1.0625 inches. Width: .625 inches. Height: .8125 inches.
Bumper, door, front of door
Bumper, door, side hood stop
Bumper, door edge.Length: 1.0 inches. Width: .625 inches. Height: .75 inches.
Bumper, door. Installs on back edge of door. Please check your car for quantities required.Usually two (2) to eight (8) per vehicle.
Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.
Bumper, door lower. Bumper pushes into slot on door at bottom.
Bumper, hood to cowl and door hinge pillar upper. May be used in both places.
Bumper, door.Width: 1.0625 inches. Height: .75 inches.