Hood Rest Pad Set
p/n: 60-0351-42
This six (6) piece Hood Rest Pad Set is self-retained in the slot on the fender ledge. Designed from the original parts for superior fitment and function.
Hood Side Upper Bumper
p/n: 70-2617-42
This Hood Side Upper Bumper is fully molded with top quality EPDM rubber. The authentic configuration for 1/4" hole. Six (6) bumpers typically required per vehicle.
Hood to Cowl Bumper
p/n: 70-1248-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1249-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1247-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Hood to Cowl Weatherstrip
p/n: 40-0475-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip can also be used as a radiator seal. Available by the foot.
Hood to Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Hood to Fender Bumper
p/n: 27-0056-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 25-0068-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 30-0304-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Hood to Radiator Weatherstrip
p/n: 20-2961-31
Seal, radiator air deflector to hood. Twenty two and one fourth (22-1/4) inches long. Two (2) piece set.
Hood Weatherstrip Retainer
p/n: 70-0564-42
Fastener, hood to cowl weatherstrip (and other uses), self-retaining button head retainer.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Insert Trim for Aluminum Footplate
p/n: 70-4639-88
This rubber Insert Trim is designed from the original part for superior fit and finish. This dense rubber extrusion footage is to be to inserted into the aluminum footplates found on Eldorado models. Available by the foot.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Interior Dome Light Lens Gasket
p/n: 70-3102-17
This Interior Dome Light Lens Gasket is designed from the original part for superior fitment and seal. This quality reproduction gasket fits between the interior dome light lens and the dome light housing or bezel.
Leading Edge Weatherstrip
p/n: 70-2002-80
Rear door window vertical seals. Fully molded rubber with metal cores.
License Plate Light Lens to Housing Gasket
p/n: 20-0489-17
This License Plate Light Lens To Housing Gasket is designed from the original part for superior fitment and seal. This die cut cork reproduction gasket fits between the between lens and housing for the license plate light.
License Plate Light Mounting Pads
p/n: 60-0174-17
This rear License Plate Light Mounting Pad pair is designed from the original part for superior fitment and function. This reproduction mounting pad fits between the rear License Plate Light Housing or Bezel and the vehicle body. Two (2) required per vehicle.
Liftgate Weatherstrip
p/n: 20-3144-85
This liftgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the sides and top of the liftgate opening directly to the body.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
Lower Control Arm Bushing Seal
p/n: 60-0095-32
This Lower Control Arm Bushing Seal is designed from the original part for superior fitment and seal. Installs at the lower control arm pivot bolt bushing. Four (4) per car.
Lower Engine Mount
p/n: 20-0588-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation. One (1) required per truck.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Lower Tailgate Outer Weatherstrip
p/n: 70-4810-84
This Lower Tailgate Outer Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the outer bottom of the tailgate.
Lower Tailgate Weatherstrip
p/n: 20-3142-85
This Lower Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the bottom of the tailgate.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Outside Door Handle Button Pad
p/n: 20-0569-69
This Outside Door Handle Button Pad is designed from the original part for superior fitment and seal. This pad fits between the door handle and door button.
Outside Door Handle Mounting Pads
p/n: 20-0568-69
This Outside Door Handle Mounting Pad set is designed from the original part for superior fitment and function. This four (4) piece molded rubber set does two (2) doors.
Overdrive Cable Grommet
p/n: 20-1812-20
This Overdrive Cable Grommet is used to help protect the overdrive pull cable when passing through the sheet metal of the firewall.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Parking Brake Boot
p/n: 60-0145-24
This Parking Brake Boot is used for the brake lever at the floor. Designed from an original part and molded from EPDM dense rubber for durability and proper fit.
Parking Brake Pedal Pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Parking Light Lens Gasket
p/n: 70-1521-16
Gasket, parking light lens.Length: 14.875 inches. Width: 2.0 inches.
Parking/Backup Light Lens Gaskets
p/n: 70-1272-16
This Parking/Backup Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Housing or Bezel. Die-cut from one-eighth (1/8") inch sponge rubber.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Power brake pedal pad
p/n: 70-2411-22
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Power Steering Bushing
p/n: 70-1968-36
Bushing, power steering cylinder to frame. Two (2) required per car.Height: .625 inches.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Quarter Window Filler
p/n: 20-3085-62
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Quarter Window Filler
p/n: 70-3431-67
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Quarter Window Pads
p/n: 20-3124-79
This Quarter Window Pad pair is designed from the original part for superior fitment and seal. This is the front lower corner quarter window pad for Hardtops, Convertibles and Retractable Hardtop models.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Quarter window weatherstrip
p/n: 70-1868-77
Weatherstrip, rear quarter window. Fully vulcanized into a ring.
Quarter Window Weatherstrip
p/n: 70-2421-77
This Quarter Window Weatherstrip set contains the left and right seals for two (2) fixed windows on the rear quarter of the vehicle. These weatherstrips are properly molded with proper cross section for a precise, factory fit.