Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Firewall Grommet
p/n: 27-0026-20
This Firewall Grommet is used to run the control cables, tubes, and wires through the firewall. The two (2) hole type fits a three fourths (3/4) inch by one and five sixteenths (1-5/16) inch hole.
Engine Mount Pad
p/n: 11-0027-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Top Of Door Weatherstrips
p/n: 20-2110-73
This Top of Door Weatherstrip pair is designed from the original part for superior fitment and seal. These weatherstrips mount (glue-on) directly to the vehicle body to seal the doors when closed.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Vent window weatherstrip
p/n: 20-2046-52
Seals, wind-wing bracket rubber. Holds glass in place. Four (4) piece set. Replaces factory #B-7603108.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Engine Mount Bolt
p/n: 20-0309-11
This Engine Mount Bolt can be used for the front or rear. Hex head bolt drilled for cotter key.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.