Hood to Fender Bumper
p/n: 70-2046-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Cowl Drain Gutter Hose Grommet
p/n: 40-0202-54
Grommet, cowl drain. One and seven sixteenths (1-7/16) inch outside diameter for seven sixteenths (7/16) inch drain hose through firewall.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-4670-45
This four (4) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die-cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Door handle gasket
p/n: 70-2628-69
Gasket set, door handle. Machine die cut to original profile. Each set is enough for two doors.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Door Bumper
p/n: 40-0131-70
Bumper, door side. Approximate size one half (1/2) inch by three fourth (3/4) inch by two (2) inch. Length: 2.0 inches. Width: .50 inches.
Steering Column Cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Inner Fender Splash / Dust Shield Set
p/n: 70-4669-45
This four (4) piece Inner Fender Splash / Dust Shield Set is designed from the original part for superior fitment and seal. Inner Fender pieces are die-cut from quality masticated rubber to authentic original dimensions. These pieces fit to the inner front fenders.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Body Mounting Pad
p/n: 40-0232-48
Pad, body mounting, upper. Fully molded rubber with locating collar. As many as twelve (12) used per car. One and fifteen sixteenths inch (1 15/16") outside width by two inch (2") outside width. See drawing for more dimensions.
Body Mounting Pad
p/n: 40-0453-48
Insulator, body mounting. Fully molded rubber with locating collar. Use as required. Up to eight (8) are used per car.
Steering gear bushing
p/n: 40-0130-36
Bushing, insulator, for steering gear arm. Four (4) required per car.
Fuel Filler Neck Grommet
p/n: 70-2580-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Door Bumper
p/n: 40-0235-70
Bumper, door striker plate. Two (2) per door, front and rear.Length: 1.375 inches. Width: .50 inches.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
Quarter Window Vertical Leading Edge
p/n: 83-1012-80
This quarter and side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. A reproduction weatherstrip manufactured to OEM specifications to install for an authentic fit and finish.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Hood Bumper
p/n: 82-0212-42
Bumper, hood to fender ledge. Excellent reproduction, made just like original.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Hood to Fender Bumper
p/n: 70-2043-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Body Mounting Pad
p/n: 40-0231-48
Pad, body mounting, upper. Fully molded rubber with locating collar. One and fifteen sixteenths inch (1 15/16") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") inside locating hole diameter.
Door Bumper
p/n: 70-2292-70
Steele Rubber Products has the best quality door bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Body Mount Isolator Pad
p/n: 40-0234-48
This Body Mount Isolator Pad functions as a body to frame isolator mounting pad. Made of high quality EPDM rubber with a high level of fit and finish.
Body Mounting Pad
p/n: 40-0230-48
Pad, body mounting, lower. Fully molded rubber. One and eleven sixteenths inch (1 11/16") outside diameter by nine sixteenths inch (9/16") inside hole diameter by one half inch (1/2") height.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Handle Gasket
p/n: 40-0133-70
Pad, door handle escutcheon. Two and three fourths (2-3/4) inch by one and one fourth (1-1/4) inch.Width: 2.75 inches. Height: 1.25 inches.
Door Jamb Bumper Pad
p/n: 40-0042-70
This Door Jamb Bumper Pad is designed from the original part for superior fitment and seal. A reproduction of earlier type, screw retained and a perfect copy.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Battery Cable Grommet
p/n: 40-0333-21
Grommet, battery hot cable through frame. Three fourths (3/4) inch inside diameter for one and three sixteenths (1-3/16) inch hole through frame.
Body Mounting Pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Door opening step grommet
p/n: 40-0125-49
Grommet, door sill mat retainer at lower door opening. All sill plates with metal stud retainer. (Included in our #40-0542-49 set).
Windshield Bumper
p/n: 40-0366-52
This Windshield Bumper is designed from the original part for superior fitment and seal. Two (2) per car.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
1-1/16" Spare Wheel Carrier Grommet
p/n: 32-0253-37
This Spare Wheel Carrier Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for spare wheel carrier mounting bracket.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
7/8" Window Weatherstrip
p/n: 40-0054-99
This Window Weatherstrip is typically used on the rear window and rear fixed quarter window. Used on cars with chrome reveal molding where the reveal molding lays over the pinchweld seal. Available by the foot.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
1" Frame Hole Plug
p/n: 35-0166-44
Plug, for holes in right hand frame rail when car is left hand drive. (Frames were punched for both right hand and left hand drive).
Spring Shackle Bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
29/32" Side Mount Grommet
p/n: 32-0364-37
This Side Mount Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for side tire carrier support arm bracket.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32") inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons and other project uses.
Trunk Decklid Bumpers
p/n: 70-2044-87
This Trunk Decklid Bumper pair is designed from the original part for superior fitment, finish and function. These rubber bumpers attach to the trunk decklid to support / cushion lid closure.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Door Weatherstrip
p/n: 70-1448-73
This Door Weatherstrip for the door sill is made of an extruded dense rubber. Available by the foot.
Door Weatherstrip
p/n: 70-1292-73
This Door Weatherstrip is used on the bottom of the door opening. Available by the foot.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Side Roof Rail Weatherstrip
p/n: 70-0155-65
Weatherstrip, convertible roof rail. Available by the foot.
Glass up stop bumper
p/n: 70-3623-62
Front door glass up stop bumper. For models w/out power vent windows. Use two (2) or four (4) per vehicle. Refer to your vehicle to see how many are required.
Door Weatherstrip
p/n: 40-0487-73
This Door Weatherstrip is made of a high-quality dense rubber. The weatherstrips is commonly used as a bottom door weatherstrip but can be for a variety of uses. Available by the foot.
Trunk Weatherstrip
p/n: 40-0479-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
3/4" Window Weatherstrip
p/n: 40-0053-99
This Window Weatherstrip is used for rear window and rear fixed quarter windows. Available by the foot.
Hood to Cowl Weatherstrip
p/n: 40-0475-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip can also be used as a radiator seal. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
11/16" Roof Rail Weatherstrip
p/n: 70-1171-99
This available by the foot Roof Rail Weatherstrip measures eleven sixteenths inches (11/16") in height. It fits into a metal channel retainer. Note: Order twelve feet (12') for two (2) door models and fourteen feet (14') for four (4) door models.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
Hood to Fender Bumper
p/n: 40-0503-42
Bumper, hood to fender ledge. Correct original cross-section. Up to ten (10) required per car.
Side Window Bumper
p/n: 40-0116-70
Pad, side window anti-rattle. Five sixteenths (5/16) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal.
7/16" Rear Window Weatherstrip
p/n: 30-0044-77
This Rear Window Weatherstrip is made of a high-quality EPDM dense rubber. Extra light, plain channel for one fourth (1/4) inch glass. Three thirty seconds (3/32) inch thick wall. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1191-52
This Window Weatherstrip is for models without chrome reveal molding. Available by the foot.