Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3068-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Hood To Fender Bumper Set
p/n: 20-0033-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Radiator Support To Hood Weatherstrip
p/n: 20-1452-42
This Radiator Support To Hood Weatherstrip is designed from the original part for superior fitment and seal. Includes staples to install. This weatherstrip works to seal the hood to the radiator support for better engine cooling.
Hood Bumper
p/n: 20-0014-42
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Trunk Weatherstrip
p/n: 70-3923-84
This Trunk Weatherstrip is made from top quality rubber to ensure durability and designed from the original part for a superior fitment and seal. The seal mounts around the full perimeter of the trunk and directly to the body.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Taillight & Back Up Light Lens Gasket Set
p/n: 70-3310-15
This six (6) piece Taillight Lens and Back Up Light Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight / back up light lens and housing.
Radiator top seal
p/n: 20-0130-31
Seal, radiator support top to hood. Includes special plastic buttons to install. For models with A/C.
Taillight Lens Gaskets - In Fin
p/n: 70-3117-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens & taillight housing in fin.
Tailgate weatherstrip
p/n: 20-1526-87
Weatherstrip, tailgate lower glass sash channel. Goes between glass and channel.
Door Weatherstrip
p/n: 70-1650-70
Seal, rear door at rear of window.Length: 1.75 inches. Width: .875 inches.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Front Lower Engine Mount
p/n: 20-0596-11
This Front Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.