Door Weatherstrip
p/n: 70-1448-73
This Door Weatherstrip for the door sill is made of an extruded dense rubber. Available by the foot.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Door Weatherstrip
p/n: 70-1292-73
This Door Weatherstrip is used on the bottom of the door opening. Available by the foot.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
Lower Control Arm Bushing Seal
p/n: 60-0095-32
This Lower Control Arm Bushing Seal is designed from the original part for superior fitment and seal. Installs at the lower control arm pivot bolt bushing. Four (4) per car.
Taillight Lens Gasket
p/n: 20-1988-15
Gasket, taillight lens. Inner and outer seal. Enough for one taillight lens.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
1-9/16" Firewall Grommet
p/n: 32-1201-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Emergency Brake Cable Grommet
p/n: 20-2310-24
This Emergency Brake Cable Grommet is used when running the brake cable to the frame. Made from high-quality dense rubber to provide excellent durability.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Quarter Window Weatherstrip
p/n: 18-0004-77
Weatherstrip, stationary quarter window. Available by the foot.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Body Mounting Pad
p/n: 70-0264-48
This Body To Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs under body mount / washer below bracket. Fully molded high quality EPDM rubber.
2-1/4" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Firewall Retainer
p/n: 30-0207-20
Fastener, firewall insulation. Three fourths (3/4) inch diameter head by one (1) inch long.Height: 1.0 inches.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Engine Mount Bolt
p/n: 20-0309-11
This Engine Mount Bolt can be used for the front or rear. Hex head bolt drilled for cotter key.
Windshield Bumper
p/n: 34-0258-52
Bumper (stop), swing out windshield against dash. Steel core, nine sixteenths (9/16) inch diameter by five sixteenths (5/16) inch thick. Replaces #3681093. Two (2) per vehicle.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
1-3/8" Firewall Grommet
p/n: 70-0712-20
This Firewall Grommet is designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability. Two (2) holes in grommet.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Rear Leaf Spring & Shackle Bushing
p/n: 70-0182-32
This Rear Leaf Spring Bushing is designed from the original part for superior fitment and function. Bushing is for the rear leaf spring front or rear spring to shackle. Two bushings pushed together form one complete bushing. May require eight (8) or twelve (12) each depending or vehicle model if replacing all bushings.
Choke and Throttle Rod Grommet
p/n: 20-2279-88
This Choke and Throttle Rod Grommet is used where the choke and throttle pass through the dash. Designed from the original part for superior fit and seal.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Door Bumper
p/n: 60-0048-71
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.
Black Door Lock Knob
p/n: 30-0251-71
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Door Handle Gasket
p/n: 40-0133-70
Pad, door handle escutcheon. Two and three fourths (2-3/4) inch by one and one fourth (1-1/4) inch.Width: 2.75 inches. Height: 1.25 inches.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Body Mounting Pad
p/n: 40-0230-48
Pad, body mounting, lower. Fully molded rubber. One and eleven sixteenths inch (1 11/16") outside diameter by nine sixteenths inch (9/16") inside hole diameter by one half inch (1/2") height.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Firewall Grommet
p/n: 27-0026-20
This Firewall Grommet is used to run the control cables, tubes, and wires through the firewall. The two (2) hole type fits a three fourths (3/4) inch by one and five sixteenths (1-5/16) inch hole.
Rear Stabilizer Bushing
p/n: 70-0905-33
Bushing, rear stabilizer ends. Four (4) required per car. Fully molded rubber.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Body Mounting Pad
p/n: 40-0231-48
Pad, body mounting, upper. Fully molded rubber with locating collar. One and fifteen sixteenths inch (1 15/16") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") inside locating hole diameter.
Wiper Transmission Gasket
p/n: 70-0499-53
Gasket, wiper transmission mounting. Replaces #4089635 for smaller type wiper gear, about 7/8" X 1-1/8". Early series models only.
2" Spare Wheel Carrier Grommet
p/n: 32-0355-37
This Spare Wheel Carrier Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the rear wheel carrier bracket base.
1-11/16" Firewall Grommet
p/n: 32-0160-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 60-0027-48
Pad, side body mounting. Fully molded rubber, rectangular. Two and seven-sixteenths inch (2-7/16") outside length by one and five-eights inch (1-5/8") outside width by one-fourth inch (1/4") height.
Steering Column Vacuum Shift Cylinder Boot
p/n: 60-0556-24
This Steering Column Vacuum Shift Cylinder Boot is designed from the original part for superior fitment, function and appearance. Perfectly engineered duplicate of original. Constructed of durable long lasting rubber. Length: 4-3/8" inches.
1-3/8" Firewall Grommet
p/n: 50-0531-20
This Firewall Grommet is used to run the oil pressure, water temperature, and vacuum line through the firewall. Designed from original part for excellent workmanship.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Door Bumper
p/n: 30-0032-71
Pad, for door. Circular shape, one and one fourth (1-1/4) inch diameter.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.