Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Headlight grommet
p/n: 25-0039-14
Base, headlight wire conduit and support post. (Vertical post under headlight).
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Accelerator Pedal Pad
p/n: 10-0001-40
Pad, accelerator pedal. Cements and fastens with screws to original metal pedal. Length: 6.50 inches.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
