Steering Column At Floor Seal
p/n: 70-3490-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. The seal is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Firewall To Hood Bumpers
p/n: 20-2758-42
These Firewall To Hood Bumpers are a quality reproduction of the original factory part. Includes attaching screws. Three (3) piece set.
Parking Light Housing Gaskets
p/n: 20-0612-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Housing or Bezel and the body of the vehicle.
PCV valve grommet
p/n: 20-2695-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Pickup tie down mounting pad
p/n: 20-0885-45
Pad, pickup box tie down hook. Eight (8) required per truck.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Front Fender or Quarter Panel Extensions
p/n: 20-2761-45
This Front Fender or Rear Quarter Panel Extension pair is designed from the original part for superior fitment and seal. The pair comes as one solid unit that is perforated for the customer to split apart and is easy to install.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Door drain hole seal
p/n: 70-3034-70
Seal, door inner panel drain. Attaches to bottom of door with one (1) carrot retainer on either end.
Door Plug
p/n: 70-4537-45
This Door Plug is designed from the original part for superior fitment and function. Plug is made from high-quality EPDM 60 durometer dense rubber to provide excellent durability and service.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Trunk Decklid Bumpers
p/n: 70-2044-87
This Trunk Decklid Bumper pair is designed from the original part for superior fitment, finish and function. These rubber bumpers attach to the trunk decklid to support / cushion lid closure.
Firewall Plug - Oval Rubber
p/n: 20-0754-20
This Firewall Plug is designed from the original part for superior fitment and finish. Usually requires three oval plugs per truck.
Windshield Wiper Pivot Gaskets
p/n: 20-0891-53
This Windshield Wiper Pivot Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket is die cut from original style EPDM rubber for an authentic fitment, finish and function.
License Plate Light Lens Gasket
p/n: 70-3497-17
This License Plate Light Lens Gasket is designed from the original part for superior fitment and seal. This gasket fits between license plate light lens and housing.
PCV valve grommet
p/n: 20-2697-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
Glass up stop bumper
p/n: 70-3623-62
Front door glass up stop bumper. For models w/out power vent windows. Use two (2) or four (4) per vehicle. Refer to your vehicle to see how many are required.
Wiper Transmission Gasket
p/n: 20-2779-53
Seal, wiper motor to firewall. Replaces factory #D1ZZ-17430.
Hood, Door Or Liftgate Bumpers
p/n: 20-0907-71
This Hood, Door Or Liftgate Bumper pair is a quality reproduction of the original factory part.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
Gearshift Seal
p/n: 20-2876-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
Hood to Fender Bumper
p/n: 70-4176-42
This Hood to Fender Bumper is a quality reproduction of the factory part. This rubber bumper attaches to the front fender to support or cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
Hood Bumper Cap
p/n: 70-1651-42
This Hood Bumper Cap is fully molded and designed from the original part for superior fitment and seal. Slip-over style application.
Parking Brake Cable To Floor Seal
p/n: 20-0853-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment and seal. This works to seal the parking brake cable as it passes through the truck floor pan.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
PCV valve grommet
p/n: 20-2696-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Side Seals
p/n: 70-4009-85
This Tailgate Side Seals includes right and left side with installation screws. These seals are properly molded from originals for a factory like fit.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Body Hole Plug
p/n: 20-0844-20
Plug, cowl side panel inner. One and seven eighths (1-7/8) inch diameter. Two (2) each required per truck.
Door Bumper
p/n: 70-2045-71
This Door to Body Bumper is quality reproduction of the original factory part. Use varies depending upon model and body type. Some models uses four (4) bumpers for front doors and four (4) for rear doors.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Body Hole Plug
p/n: 20-0845-20
Plug, oval floor pan front. Rubber. One half (1/2) inch by one (1) inch diameter. Two (2) each required per truck.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
Hood To Fender Bumper
p/n: 70-1836-42
This Hood To Fender Bumper is designed from the original part for superior fitment, finish and function. This bumper is manufactured with quality EPDM dense rubber and measures 1-7/16" x 11/16" inches.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Fuel Filler Door Bumper
p/n: 33-0538-41
This Fuel Filler Door Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the Fuel Filler Door to support / cushion the closure and prevent metal to metal contact. Usually requires two (2) bumpers each per vehicle.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
7/8" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
7/8" Trunk Bumper
p/n: 33-0990-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Rear Side Marker Light Gaskets
p/n: 20-2678-16
This Rear Side Marker Light Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits in the rear between the side marker light and the vehicle body.
Rear License Plate Bracket Bumper
p/n: 70-4478-45
This Rear License Plate Bracket Bumper is designed from the original part for superior fitment and function. This OEM exact copy reproduction bumper mounts in the spring retainer on the license plate bracket.
Glovebox and License Plate Bumper
p/n: 20-2889-45
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Hood to Fender Bumper
p/n: 82-0022-42
This single molded Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
15/16" Trunk Bumper
p/n: 33-0350-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Bumper fits to the rear compartment lid, lower corners on lid. Two (2) per car. Manufactured to OEM specifications to install for an authentic fit, finish, and function.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
Hood Weatherstrip Clip
p/n: 70-1255-42
Clip, hood to cowl weatherstrip. Normal usage is fourteen (14) to sixteen (16) per car as needed.
License Plate Light or Heater Motor Wire Grommet
p/n: 20-1815-20
This License Plate Light or Heater Motor Wire Grommet is designed from the original part for superior fitment and function. This part functions as a License Plate Light Grommet(s) for Bronco and as a Heater Motor Wire Grommet for 1957-1958 Ford Car models.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.