Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
License Plate Light or Heater Motor Wire Grommet
p/n: 20-1815-20
This License Plate Light or Heater Motor Wire Grommet is designed from the original part for superior fitment and function. This part functions as a License Plate Light Grommet(s) for Bronco and as a Heater Motor Wire Grommet for 1957-1958 Ford Car models.
Hood Weatherstrip Clip
p/n: 70-1255-42
Clip, hood to cowl weatherstrip. Normal usage is fourteen (14) to sixteen (16) per car as needed.
Hood to Fender Bumper
p/n: 82-0022-42
This single molded Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Rear Side Marker Light Gaskets
p/n: 20-2678-16
This Rear Side Marker Light Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits in the rear between the side marker light and the vehicle body.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Rear License Plate Bracket Bumper
p/n: 70-4478-45
This Rear License Plate Bracket Bumper is designed from the original part for superior fitment and function. This OEM exact copy reproduction bumper mounts in the spring retainer on the license plate bracket.
Corner Joint Sleeves
p/n: 70-3720-52
Corner Joint Sleeve pair for the bottom corners of rear window gaskets that require a locking strip. These joint sleeves have a Chrome look to match the Mylar locking strip. Joint sleeves can also be painted black when using with the black rubber locking strip.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Hood To Fender Bumper
p/n: 70-1836-42
This Hood To Fender Bumper is designed from the original part for superior fitment, finish and function. This bumper is manufactured with quality EPDM dense rubber and measures 1-7/16" x 11/16" inches.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Front Fender Plugs
p/n: 20-0753-20
This Front Fender Plug pair is a reproduction manufactured to OEM specifications to install for an authentic fit and finish. Used on the top of the front fender towards the rear to help reduce heat and fumes from entering the cab.
Hood to Fender Bumper
p/n: 70-1638-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Two (2) required per car.
Tailgate Side Seals
p/n: 70-4009-85
This Tailgate Side Seals includes right and left side with installation screws. These seals are properly molded from originals for a factory like fit.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Hood to Fender Bumper
p/n: 70-1637-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Two (2) required per car.
Hood Bumper Cap
p/n: 70-1651-42
This Hood Bumper Cap is fully molded and designed from the original part for superior fitment and seal. Slip-over style application.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
Hood to Fender Bumper
p/n: 70-4176-42
This Hood to Fender Bumper is a quality reproduction of the factory part. This rubber bumper attaches to the front fender to support or cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
Hood to Fender Bumper
p/n: 70-1639-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Two (2) required per car.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Hood, Door Or Liftgate Bumpers
p/n: 20-0907-71
This Hood, Door Or Liftgate Bumper pair is a quality reproduction of the original factory part.
Hood bumper
p/n: 70-2876-42
Bumper, hood adjustable, rear. Slip-over rubber cover for threaded stud that mounts on both sides of cowl.
Fuel Filler Neck Gasket
p/n: 70-4920-39
This Fuel Filler Neck Gasket is designed from the original part for superior fitment and seal. Machine stamped from quality materials to authentic original dimensions.
Firewall Plug - Oval Rubber
p/n: 20-0754-20
This Firewall Plug is designed from the original part for superior fitment and finish. Usually requires three oval plugs per truck.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Pickup tie down mounting pad
p/n: 20-0885-45
Pad, pickup box tie down hook. Eight (8) required per truck.
Taillight Mounting Pad
p/n: 70-3564-15
Gasket, taillight mounting pad. Eight (8) used per car. Machine die cut 5/8" thick sponge rubber seals tail light assembly to body. Included in our kit part number #70-3566-15.
Steering Column At Floor Seal
p/n: 70-3490-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. The seal is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Parking Light Housing Gaskets
p/n: 20-0612-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Housing or Bezel and the body of the vehicle.
Parking Light Lens Gaskets
p/n: 20-2683-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Hood bumper
p/n: 70-2871-42
Bumper, hood, front adjustable. Bumper threads into radiator support on left and right side. Two (2) required per car.
Bronco Script Brake OR Clutch Pedal Pad
p/n: 70-4480-22
This reproduction Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedals for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Windshield Molding Joint Cover With Wide Moldings
p/n: 70-4483-52
This Windshield Molding Joint Cover is designed from the original part for superior fitment and usage. This cover is made from Stainless Steel to cover the molding joint where the Windshield rubber comes together.
Windshield Frame Lower Weatherstrip
p/n: 70-4477-52
This Windshield Frame To Body Lower Weatherstrip is designed from the original part for superior fitment and sealing. This is the lower windshield frame hinge weatherstrip. It mounts to seal between the windshield frame and the cowl with the bead facing to the inside of the vehicle.
Trunk Emblem Gasket
p/n: 70-3220-87
This single Trunk Emblem gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) trunk / decklid emblem mounting.
Tailgate Bumper
p/n: 20-0801-45
This Tailgate Bumper is used as a retaining support. Two (2) are required per truck.
Tailgate Lower Seal
p/n: 70-4010-85
This Tailgate Lower Seal is properly molded from originals for a factory like fit. The seal is installed using screws, which are included.
Door Handle Gasket Set
p/n: 70-1647-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Body Hole Plug
p/n: 20-0764-24
Plug, fill hole. Used where clutch rod goes on standard transmission.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
F-150 Brake OR Clutch Pedal Pad
p/n: 70-4486-22
This reproduction F-150 Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Bronco Script Brake Pedal Pad, Automatic
p/n: 70-4481-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for automatic transmissions with power brakes.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
Rear Hatchback Door Window Glass Weatherstrip
p/n: 70-4826-81
This Rear Hatchback Door Window Glass Weatherstrip is designed from the original part for superior fitment and seal. A reproduction of edge channel that surrounds the metal edge were the rear hatch window glass touches the hatch door.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
F-150 Brake Pedal Pad, Automatic
p/n: 70-4487-22
This reproduction F-150 Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
F-100 Brake Pedal Pad, Automatic
p/n: 70-4485-22
This reproduction F-100 Brake Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
Side Window Glass Run Channel
p/n: 20-0812-58
This Side Window Glass Run Channel is designed from the original part for superior fitment and seal. Single length of flexible window run channel for the sides and top of door windows. For Left or Right side, order two (2) per truck as needed.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 70-4014-42
This Firewall To Hood Weatherstrip - Cowl Lacing comes with pre-drilled mounting holes and mounting clips installed. Made of high-quality EPDM rubber and to the original design for a factory like fit and appearance.
Brake Pedal Pad
p/n: 70-4590-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads. Detailed and finished to match the original appearance.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Parking Brake Cable To Floor Seal
p/n: 20-0760-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment, finish and function. The part protects the parking brake cable as it passes through the truck body floor pan.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Hood Bumper Set
p/n: 20-0792-42
This Hood Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) piece set.
Turn signal light gasket
p/n: 20-0749-16
Gaskets, side marker light. Front and rear. Four (4) piece set.
Side Marker Light Gaskets
p/n: 70-4335-17
This Side Marker Light Gasket set is designed as a premium upgrade over the original part for superior fitment and a highly finished look. Fully molded gaskets installs between the side marker and body when not using a chrome bezel.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Tailgate Drain Seals
p/n: 70-4007-84
This Tailgate Drain Seal pair includes right and left sides that install at the bottom of the tailgate. These seals are properly molded from originals for a factory like fit.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Firewall to Hood Weatherstrip
p/n: 70-3123-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. Installs with the pre-installed clips on the front edge of the cowl.
Windshield Wiper Pivot Gaskets
p/n: 20-0808-53
This four (4) piece Windshield Wiper Pivot Gasket set is designed from the original part for superior fitment and seal. This reproduction gasket is die cut from original style EPDM rubber for an authentic fitment, finish and function.
Taillight Lens Gaskets
p/n: 20-2667-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment, finish and function. These reproduction gaskets fit between taillight lens and taillight housing.
Cowl to Fender Seals
p/n: 70-3340-43
This two (2) piece Cowl to Fender Seal pair is designed from the original part for superior fitment and seal. Fender seals are die cut from quality masticated rubber to authentic original dimensions.
Paint Reseal and Gasket Set
p/n: 70-4310-44
This Paint Reseal Gasket Set contains like original design reproductions for the vehicles specific exterior pieces. These reproductions are die-cut from quality materials to the original design for superior performance, durability, and a factory like fit.