Hood Corner Pad
p/n: 60-0042-42
Pads, hood corners, right and left. Four (4) piece set.Width: 1.125 inches. Height: 1.125 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
Hood Corner Pad Set
p/n: 20-2018-42
This twelve (12) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. The set includes grille area and cowl bumpers as required.
Hood Corner Pad Set
p/n: 20-2015-42
This fourteen (14) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. Includes grille area and cowl bumpers as required.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Hood Inner Center Rest Pad
p/n: 30-0222-42
This Hood Inner Center Rest Pad pair is designed from the original part for an authentic fit, finish, and appearance. Rubber only pads that fit original bracket.
Hood Louver Corner Stop
p/n: 33-0129-42
Corner stop, hood louver, self-holding, original size and profile, fits one fourth (1/4) inch hole in sheet metal.
Hood to Cowl Fabric Lacing
p/n: 20-2022-43
This Hood To Cowl Fabric Lacing is designed from the original part for superior fitment and seal. This lacing attaches to the cowl at the rear of the engine bay to fit between the hood and cowl with hood closure.
Horn Cover Bumper
p/n: 30-0283-21
Bumpers, horn cover. Rubber with brass core construction like original.Length: 4.0 inches. Width: .625 inches.
Horn Trumpet Grommet
p/n: 70-1199-21
Grommets, horn trumpet mounting. Seven eighths (7/8) inch inside diameter. For the one (1) inch inside diameter see our #70-1200-21.
Horn Trumpet Grommet
p/n: 70-1200-21
Grommets, horn trumpet mounting. One (1) inch inside diameter, 1-3/8 inch outside diameter, 9/16 inch high.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Lower Door Weatherstrip
p/n: 20-2118-73
This three (3) piece lower door weatherstrip set is designed from original parts for superior fitment and seal. These lower seals mount directly to the lower door bottom for front and rear doors.
Lower Door Weatherstrip
p/n: 20-2117-73
This Lower Door Weatherstrip is designed from the original part for superior fitment and seal. This rubber weatherstrip mounts on the lower door bottom to seal against the vehicle body when closed.
Lower Door Weatherstrip Retainers
p/n: 20-0393-73
This Lower Door Weatherstrip Retainer pair is designed from the original part for superior fitment, finish and function. A pair of retainers for the lower door weatherstrips that mount on the left and right rocker sills. Does not include door weatherstrips.
Lower Door Weatherstrips
p/n: 20-0391-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. These secondary door weatherstrips mount in channels on the cab body at the lower door opening. Works to seal the bottom of the doors against the vehicle body when the door is closed.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Luggage Rack Grommet
p/n: 17-0021-46
Grommet, luggage rack support arm through body.Length: 2.25 inches. Width: 1.25 inches.
Parking Light Mounting Pad
p/n: 70-0253-16
Pads, parking light to fender mounting.Length: 2.875 inches.
Parking Light Mounting Pad
p/n: 30-0447-17
Pad, parking light to fender. Requires two (2) per car.Length: 4.125 inches.
Power Brake Holder
p/n: 17-0024-24
Holder, power brake B and K fitting to firewall, exact copy.Width: 1.625 inches. Height: 3.50 inches.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Glass Run Channels
p/n: 20-2079-58
This high-quality material Rear Quarter Window Glass Run Channel set is the run channel that holds the glass in place.
Quarter Window Weatherstrip
p/n: 60-0446-77
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Quarter Window Weatherstrips
p/n: 27-0040-77
This Quarter Window Weatherstrips pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the quarter glass for a precise, factory fit. For fixed, stationary windows only.
Quarter Window Weatherstrips
p/n: 20-2122-77
This Quarter Window Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the left and right rear quarter glass for a precise, factory fit. Ends are not bonded. For stationary windows only.
Radiator Mounting Pad
p/n: 30-0451-31
Spacer or Pad, lower radiator anchor stud. Used in conjunction with our #30-0395-31.Height: .3125 inches.
Radiator Mounting Pad
p/n: 30-0395-31
Spacer or Pad, radiator anchorage stud, upper stud. One (1) pair required per car.Length: 2.5625 inches.
Radiator Mounting Pad
p/n: 30-0209-31
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.
Rear Axle Bumpers - Revulcanization
p/n: 11-0030-35
This Rear Axle Bumpers - Revulcanization is designed to restore your original rubber bumper pads to a like new condition. Service requires your metal cores. Please call or email for more service details and ordering. Revulcanization service only.
Rear Bumper Grommet
p/n: 60-0406-28
Grommets, rear bumper. Right and left sides. Left side has clearance for tail light wire.
Rear Bumper Grommet
p/n: 40-0180-30
Grommet, rear bumper support bar to gas tank apron. One and three fourths (1-3/4) inch inside diameter.
Rear Bumper Grommet
p/n: 40-0112-30
Grommets, rear bumper symmetrical, right and left. Perfect detailing on both inner and outer surfaces. Fully molded rubber.
Rear Bumper Grommet
p/n: 40-0296-30
Grommets, rear bumper clamp to frame end. Comes as a four (4) piece set. Fully molded rubber.
Rear Bumper Grommet
p/n: 50-0061-29
Grommets, rear bumper, hollow construction, superb copy, three and one half (3-1/2) inch high. Similar to our #50-0086-29.Length: 4.25 inches.
Rear Engine Support Assembly - Revulcanization Only
p/n: 30-0328-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear Engine Support Pad
p/n: 70-0742-11
This Rear Engine Support Pad is used as a cushion at transmission. Four (4) piece set.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0034-76
This six (6) piece Rear Quarter Vent Window Weatherstrip set is designed from the original part for superior fitment and seal. Set includes the division post seals.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0066-76
This Rear Quarter Vent Window Weatherstrip set is designed from the original part for superior fitment and seal. Set includes the division post seals.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0043-76
This six (6) piece Rear Quarter Vent Window Weatherstrip set is designed from the original part for superior fitment and seal. Set includes the division post seals.
Rear Spare Wheel Carrier Seal
p/n: 40-0141-37
Grommet, rear spare wheel carrier.Some models require 3 pieces (1-1/2 prs).Length: 3.375 inches.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rear Spring Pad
p/n: 27-0010-35
Pad, rear spring insulator for one and three fourths (1-3/4") inch wide springs. Four (4) per vehicle.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 20-0394-81
This Rear Window Gasket is made just like the original and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 30-0392-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Designed to be used with reveal molding (not included).
Rear Window Gasket
p/n: 60-0367-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0513-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Designed to be used with reveal molding.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Roof Tack Strip Insert Weatherstrip
p/n: 20-2032-45
This Roof Tack Insert Weatherstrip is designed from the original part for superior fitment and seal. This insert strip seal fits between roof insert and the body of the vehicle. Closed Cars Only
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumble Seat Lid Bumper Pad
p/n: 40-0297-85
Bumper, rumble seat lid. Sometimes used on trunk. One half (1/2) inch by one (1) inch by one (1) inch. Two (2) per car.Length: 1.0 inches. Width: 1.0 inches.
Rumble Seat Step Mounting Pad
p/n: 70-0262-45
Pad, rumble seat step plate mounting, rectangle type for top of fender.Length: 4.875 inches. Width: 4.25 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Step Pad
p/n: 11-0012-87
Cover, rumble seat step pad, slipover type, excellent copy.Width: 5.0 inches. Height: 5.0 inches.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Rumble Seat Step Pad
p/n: 40-0055-44
Pad, rumble seat step, with "DeSoto" logo, full slipover type to fit old carcass and outer trim ring. See also our #40-0353-44.Height: .50 inches.