Trunk Bumper
p/n: 70-2741-87
Bumpers, adjustable trunk. Screws into trunk. Two (2) required per car.
Wiper Transmission Gasket
p/n: 20-2779-53
Seal, wiper motor to firewall. Replaces factory #D1ZZ-17430.
Hood Bumper
p/n: 70-2735-42
This adjustable Hood Bumper mounts at the front of the vehicle over the radiator. 1.0 x 44mm thread with 23mm hex head.
Wiper Transmission Gasket
p/n: 20-1609-53
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Gearshift Seal
p/n: 20-2876-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Gearshift Seal
p/n: 20-2875-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Wiper Transmission Gasket
p/n: 20-1610-53
Seal, wiper pivot shaft to cowl. Large type. Replaces factory #7C-17541.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
Speedometer Cable Grommet
p/n: 20-2435-20
This Speedometer Cable Grommet is used to protect the cable when running it through the firewall. Designed from the original part for superior fit and seal.
Wiper Hose Grommet
p/n: 20-2524-53
This Wiper Hose Grommet is used to protect the wire when running it through the firewall. Designed from the original part for superior fit and seal.
Air Vent Cable Grommet
p/n: 20-2437-20
This Air Vent Cable Grommet is used where the air cable passes through the firewall. One pair required per vehicle. This grommet is also commonly used for the hood pull cable, heater wire, and electric wiper motor cable.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Front Suspension Lower Inner Control Arm Seal
p/n: 20-2470-32
This Front Suspension Lower Inner Control Arm Seal is designed from the original part for superior fitment and function. Four (4) required per car.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Shock Absorber or Track Bar Bushing
p/n: 20-2476-33
This Shock Absorber or Track Bar Bushing is designed from the original part for superior fitment and function. These bushes are used on tubular-style shock absorbers and also on stabilizer track bar(s).
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Windshield Wiper Hose Grommet
p/n: 20-2300-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from the original part for superior fit and seal.
Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2723-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Made from flat foam rubber to provide protection.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2724-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Designed from original part so it fits correctly.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Hood bumper
p/n: 70-3377-42
Bumper, hood-to-fender. Slides into slot on fender flange. Four (4) required per car.
Spring Shackle or Shock Absorber Link Bushing
p/n: 20-1274-32
This Bushing is manufactured to OEM specifications to install for an authentic fit, finish and function. Used for front or rear leaf spring on Ford models. Used as a rubber, shock absorber link bushing on Chrysler models.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Door Bumper
p/n: 70-2725-71
Bumper, door, upper rear corner attaches to the door. Two (2) needed per car.
Glovebox and License Plate Bumper
p/n: 20-2889-45
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
Glovebox bumper
p/n: 20-2391-88
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Rear Side Marker Light Gaskets
p/n: 20-2678-16
This Rear Side Marker Light Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits in the rear between the side marker light and the vehicle body.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.
Fender Washer - Rubber
p/n: 20-2191-44
This quality rubber Fender Washer is designed from the original part for superior fitment and function. For the mounting of the rear fender. Large type, one and one half (1-1/2") inches diameter.
Fender Washer - Rubber
p/n: 20-2190-44
This quality rubber Fender Washer is designed from the original part for superior fitment and function. For the mounting of the front fender. Small type. One and one fourth (1-1/4") inches diameter.