Running Board Matting
p/n: 70-0420-49
Running board matting. Fully molded rubber strips with full length steel cores molded in.
Engine Mount Cushions
p/n: 70-0300-11
These Engine Mount Cushions are used as an intermediate engine mount for support bolts. Split in half if needed at installation. A four (4) piece set.
Rear Engine Support Pad
p/n: 70-0443-11
This Rear Engine Support Pad is used as a cushion at transmission. Makes a four (4) piece set after splitting.
Distributor boot
p/n: 70-0004-21
Boot, distributor dust and moisture. Original equipment, exact copy. V-16 only.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Ferrule Installing Tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Vacuum Clutch / Brake Cylinder Diaphragm
p/n: 50-0063-24
This Electromatic Clutch Control or Brake Vacuum Cylinder Diaphragm is designed from the original part for superior fitment and function. Used in different locations dependent upon vehicle make.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Windshield Weatherstrip Set
p/n: 70-0016-52
This three (3) piece Windshield Weatherstrip Set includes two 16-1/2" side weatherstrip channels and one 48" bottom weatherstrip channel. All corners are correctly molded to fit perfectly.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
Body Mounting Pad
p/n: 70-0298-48
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Vacuum Brake Cylinder Rod Boot
p/n: 70-0010-24
This Vacuum Brake Cylinder Rod Boot is designed from the original part for superior fitment and seal. Made from durable rubber to original configuration.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Engine Mount Pad
p/n: 70-1162-11
This Front Engine Mount Pad pair is designed for cars with round cone type front engines. For V-12 and V-16 models.
Firewall Grommet Set
p/n: 70-1149-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Side Mount Spare Grommet Set
p/n: 70-1136-37
This six (6) piece Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Radiator Brace Filler Strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Body Mounting Pad
p/n: 70-0299-48
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Body Mounting Pad
p/n: 70-0297-48
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Body Mounting Pad
p/n: 70-0265-48
This Body to Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs in metal bucket cups. Fully molded high quality EPDM rubber.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.