Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Front Door Vent Window Set
p/n: 90-0377-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0032-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Headlight Mounting Pad
p/n: 70-0343-14
Mounting pads, headlight bracket to fender, right and left. Length: 11.375 inches.
Hood center protector
p/n: 70-0342-42
Protector, hood center. Brass core as original threaded to fit original screws.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Luggage rack grommet
p/n: 70-0287-46
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Rear door vent weatherstrip
p/n: 38-0020-74
Weatherstrip, rear door vent. Note: we do not have a matching metal core division post seal for this part. Please order our part #70-0040-56 separately.
Rear Engine Mount
p/n: 70-0965-11
This Rear Engine Mount contains upper and lower cushions with metal washers molded in.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Rear Window Division Bar Seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Rear Window Gasket
p/n: 70-0673-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Ride Regulator Control Grommet
p/n: 70-0344-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car.Length: 5.875 inches. Width: 1.75 inches.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.