Running Board Matting
p/n: 30-0428-49
This reproduction Running Board Matting pair is designed from the original part for superior fitment, finish and function. Fully molded with crowned blocks. Top quality rubber, flawless detail. No splicing or butting required.
Running Board Trim Strips
p/n: 30-0396-49
This Running Board Trim Strip set is designed from the original part for superior fitment, finish and function. Manufactured with quality stainless steel and with retaining clips.
Engine Mount Service – Revulcanization Only
p/n: 30-0325-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Set
p/n: 90-0326-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 30-0281-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Windshield Gasket
p/n: 30-0280-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 30-0015-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Rear Window Gasket Set
p/n: 30-0368-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front Suspension Bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Transmission Mount Service
p/n: 30-0316-24
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Axle Rebound Pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Accelerator Pedal Service
p/n: 30-0474-41
Pad, accelerator pedal. Revulcanization service only.Length: 9.625 inches. Width: 1.9375 inches.
Front Spring Bumpers
p/n: 30-0087-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Front Spring Bumpers
p/n: 30-0120-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Hood Corner Pad
p/n: 30-0037-42
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Taillight Mounting Pad
p/n: 30-0318-15
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting. Length: 7.125 inches.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Cowl Vent Gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Firewall Grommet
p/n: 30-0070-21
This Firewall Grommet is used to run instrument board cables through the firewall. The oval type with masked hole for six (6) wires or cables is the necessary replacement for correct restoration.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent Window Division Bar Weatherstrips
p/n: 70-2094-56
This Front Vent Window Division Bar Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar vent window glass closes against it. Fully molded with metal core and attaching tabs.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.