Detachable Center Post Pad
p/n: 70-0295-67
Pads, detachable center post, upper and lower, steel core. One and nine sixteenths (1-9/16) inches by four and one fourth (4-1/4) inches. Four (4) piece set.
Engine Mount Service – Revulcanization Only
p/n: 50-0256-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Set
p/n: 90-0335-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0003-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine Mount Service – Revulcanization Only
p/n: 50-0234-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket
p/n: 70-0921-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front coil spring pad
p/n: 50-0306-35
Insulator ring, front coil spring, top and bottom. Four (4) per car.
Convertible Front Header Bow Weatherstrip
p/n: 70-0138-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, OUTER, right and left. This weatherstrip is molded with necessary pre-drilled end hook and screw openings to the proper clearance.
Convertible Front Header Bow Weatherstrip
p/n: 70-0157-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, INNER, right and left.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Trunk Weatherstrip
p/n: 70-1128-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Transmission Mounting Pad
p/n: 50-0335-25
Transmission support pad, insulator blocks, upper and lower.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0049-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 50-0049-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Accelerator Pedal Pad
p/n: 50-0038-40
Pad, accelerator pedal. Rubber flanges all around as original to fit over pedal core. Length: 9.125 inches.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Antenna Boot
p/n: 70-0212-21
This Antenna Boot is designed from the original part for superior fitment and function. This boot fits at the vehicle running board antenna wire connection.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Radius or Panhard Rod Bushing
p/n: 50-0303-35
This rear axle Radius or Panhard Rod Bushing is a quality reproduction of the original factory part. A fully molded rubber bushing that works to cushion road vibration at the rod end. Four (4) required per car.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
1-1/2" Firewall Grommet
p/n: 50-0299-20
This Firewall Grommet is used to run the oil pressure and water temperature lines through the firewall. Designed from original part for excellent workmanship.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
9/16" Door Edge Weatherstrip
p/n: 70-0411-73
This Door Edge Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
3/4" Roof Rail Weatherstrip
p/n: 70-1170-99
This available by the foot Roof Rail Weatherstrip measures three fourths inches (3/4") in height. It fits into a metal channel retainer. Note: Order twelve feet (12') for two (2) door models and fourteen feet (14') for four (4) door models.
7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1191-52
This Window Weatherstrip is for models without chrome reveal molding. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2-piece windshield, select gasket for division bar. Available by the foot.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Front Bow Weatherstrip Retainer Clip
p/n: 70-0527-67
This Front Bow Weatherstrip Retainer Clip is designed from the original part for superior fitment and function. This fastener is most commonly used to retain #70-0138-64 and #70-0157-64 front bow weatherstrips. A Cadmium plated retainer requiring a one-quarter (1/4) inch opening.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
5/32" Side Mount Tire Cover Seal
p/n: 50-0541-37
High-quality dense rubber seal, for a variety of uses. Available by the foot.
1" Wiring Grommet
p/n: 32-0047-14
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed to run the electric wire through the body for head and taillights.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Door Weatherstrip Fastener Clip
p/n: 70-0303-73
Metal Fastener clips, sold as an each, for attaching door edge weatherstrips. For one fourth (1/4) inch holes. Doors usually require one (1) clip per every six (6) inches.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.