Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
A/C Grommet
p/n: 70-1040-20
This A/C Grommet is used to run the air conditioning Freon lines to the chassis. Up to six (6) required per car. Designed from original part for excellent workmanship.
Door Lock Bumper
p/n: 70-0933-71
Bumper, door lock pillar, upper. Two (2) car.Length: 1.625 inches. Width: 1.0 inches.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Door Handle Gasket Set
p/n: 70-0979-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
1-3/8" Firewall Grommet
p/n: 70-1013-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Steering Column Finish Strip
p/n: 70-1031-88
Seal, steering column to instrument panel. Extruded rubber twelve (12) inch strip to exact cross-section.Length: 10.5 inches. Width: .50 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
A-Arm Dust Shields Filler
p/n: 70-2772-45
This two (2) piece A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms only.
Parking Light Lens Gasket
p/n: 70-1081-16
Gasket, fog and parking light lens housing.Length: 8.5 inches. Width: 4.0 inches.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Vent Window Division Bar Weatherstrip
p/n: 70-0703-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rear Bumper To Body Filler
p/n: 70-3078-30
This Rear Bumper To Body Filler is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. This piece fits between the rear bumper and the vehicle body.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Air Conditioning Pipe Grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Front Door Auxiliary Weatherstrips
p/n: 70-0551-73
This Front Door Auxiliary Weatherstrip pair fits to the left and right doors at the beltline. Uses snap-in fasteners, four (4) each included.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Steering Column Floorplate
p/n: 70-1425-88
Seal, steering column to firewall. For 1956 vehicles purchase our #70-1509-88 grommet separately. For 1957-58 vehicles purchase our #70-2316-88 grommet separately.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
U Jamb lock pillar filler
p/n: 50-0269-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Fender Skirt Edge Seals
p/n: 70-0897-44
Fender Skirt Edge Seal pair. Length: 60.0 inches. Width: 5/8 inches.
Hinge Pillar Weatherstrip
p/n: 70-1523-73
Weatherstrip, upper front door hinge pillar at roof rail. Molded as left and right with corrosion resistant brass metal core.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Gas Tank Filler Upper Seal
p/n: 70-3701-39
This Gas Tank Filler Upper Seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. A premium part fully molded with high quality EPDM rubber.