Hood to Cowl Bumper
p/n: 70-1249-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1247-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1248-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood Weatherstrip Retainer
p/n: 70-0564-42
Fastener, hood to cowl weatherstrip (and other uses), self-retaining button head retainer.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Quarter Window Filler
p/n: 70-3431-67
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Rear Bumper Seal
p/n: 70-1830-45
Seal, rear bumper to body. Includes two (2) thirty (30) inch strips of extrusion.Length: 30.0 inches. Width: 2.4375 inches.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.