Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
1957-1958 Cadillac Factory Shop Manual, CD
p/n: 07-1057-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory shop repair manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Vent Division Bar Weatherstrip
p/n: 70-0922-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rear Bumper End Filler Set
p/n: 70-3769-30
This four (4) piece Rear Bumper End Filler set is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
1-3/8" Firewall Grommet
p/n: 70-1013-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Fan Shroud Assembly Rubber
p/n: 70-2779-45
This two (2) piece Fan Shroud Assembly Rubber pair is designed from the original part for superior fitment and function. Shroud rubber is die cut from quality masticated rubber to authentic original dimensions. For models with Air Conditioning.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.