Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.
Brake and Clutch Pedal Pads
p/n: 25-0058-22
A pair of brake and clutch pedal pads. Two (2) per car. Length: 4 inches. Width: 2-1/2 inches.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Door Handle Gasket Set
p/n: 70-1913-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Fender Skirt Edge Weatherstrip
p/n: 60-0109-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 50-0518-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Engine Mount
p/n: 25-0060-11
This Engine Mount is for the lower front. Lower Front. Designed to original specifications for an authentic fit and appearance. The mount supports the engine and dampen vibration.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Door Auxiliary Weatherstrips
p/n: 60-0342-73
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
U Jamb lock pillar filler
p/n: 50-0307-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Trunk Weatherstrip
p/n: 50-0483-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Roof Rail Filler
p/n: 25-0069-73
Weatherstrip, front door upper corner, outer (at front end of flipper). Molded as left and right with a corrosion resistant brass metal core.
Engine Mount Service – Revulcanization Only
p/n: 25-0073-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0063-11
This Revulcanization Service Only is designed to restore your Upper Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0059-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0072-11
This Revulcanization Service Only is designed to restore your Right and Left Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Door Hinge and Bottom Weatherstrips
p/n: 50-0440-72
A Door Hinge and Bottom Weatherstrip set with molded ends. Glue in type. Four (4) pieces with fourteen (14) clips. This part is the primary door to body weatherstrip.
Windshield Gasket
p/n: 50-0212-50
This Windshield Gasket is has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the reveal molding across the top only.
Front Door Vent Window Weatherstrips
p/n: 38-0098-55
These Front Door Vent Window Weatherstrips are the main weatherstrips needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Vent Window Set
p/n: 90-0431-90
This Front Door Vent Window Set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Body Weatherstrip Kit
p/n: 90-3087-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.