Headlight Mounting Pad
p/n: 60-0211-14
Mounting pad, headlight bracket to fender.Length: 4.8125 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Brake Cable Boot
p/n: 60-0155-24
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator Pedal Pad
p/n: 60-0097-40
Pad, accelerator pedal. Slip-over type for original core. Length: 9.125 inches.
Fuel Neck Grommet
p/n: 60-0181-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and seven sixteenths inch (3-7/16") outside width by three and five eights inch (3-5/8") outside length.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Taillight Mounting Pad
p/n: 60-0545-15
Pad, bracket mounting to body for tail and license plate light. Length: 3.3125 inches. Width: 2.5625 inches.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Taillight Mounting Pad
p/n: 60-0364-15
Pad, taillight mounting to rear fender. Length: 1.0625 inches.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Taillight Mounting Pad
p/n: 60-0116-15
Pad, taillight bracket to fender. Four (4) inches long. Compare with our #60-0172-15 and #60-0545-15. Length: 4.0 inches.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.