Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Crown Molding Mounting Pad
p/n: 50-0244-44
Mounting pads, rear fender crown molding. Requires two (2) per car.Length: 40.625 inches.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Weatherstrip
p/n: 70-0857-73
Weatherstrip, front door lock pillar. Ready to install with molded ends.Length: 36.0 inches. Width: .625 inches. Height: .625 inches.
Door Weatherstrip Hinge Pillar
p/n: 50-0268-73
Weatherstrip, body hinge pillar to door, bellows type seal.
Engine Mount Service – Revulcanization Only
p/n: 50-0297-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
Front Bow Weatherstrip
p/n: 70-0785-64
Weatherstrip, front bow of convertible. Sponge rubber extrusion of correct dimensions.Length: 60.0 inches. Width: .8125 inches.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Front Door Vent Window Set
p/n: 90-0457-90
This Front Door Vent Window Set is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0085-55
This Front Door Vent Window Weatherstrips contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Front Door weatherstrip
p/n: 50-0558-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Parking, Signal or Backup Light Lens Gaskets
p/n: 50-0381-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel. Also fits Backup Light Lens on cars with optional Backup Lights.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.