Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Trunk Hinge Mounting Pad
p/n: 50-0106-87
Mounting pads, trunk hinge, four (4) piece set. Models with outside hinges.Length: 8.25 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Accelerator Pedal Pad
p/n: 60-0448-40
Pad, accelerator pedal, slip-over type. Attaches to your original pedal core, does not include attachment or linkage sockets.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent Division Bar Weatherstrip
p/n: 60-0509-56
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.