Glovebox Door Check Grommet
p/n: 70-0467-88
Grommet, glovebox door check link, for one (1) inch slot in dash.
Gravel Shield
p/n: 50-0439-44
Gravel shield, rear fender. Fully molded with metal backing and attaching tabs.Length: 15.75 inches.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Mounting Pad
p/n: 50-0462-14
Headlight housing to fender gasket. Steel rule die-cut replacement for #1320452.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 34-0311-42
Bumper, hood, fastened to cowl at rear of hood. Steel core. One and eleven sixteenths (1-11/16) inch diameter. Two (2) per car.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Parking/Backup Light Lens Gaskets
p/n: 70-1272-16
This Parking/Backup Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Housing or Bezel. Die-cut from one-eighth (1/8") inch sponge rubber.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Radiator bracket cushion
p/n: 50-0324-42
Bumper for bracket, radiator upper panel to grill. Use original steel bracket.Buick 1941: 1 required per car. 1942: Part not used for this year.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Rear Window Gasket
p/n: 60-0278-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Steering Knuckle Support Seal
p/n: 50-0199-35
This Steering Knuckle Support Seal is designed from the original part for an authentic fit, finish, and appearance. Fits at the steering knuckle support at the upper pivot pin. Four (4) required per car.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Taillight Mounting Pad
p/n: 50-0173-15
Pad, taillight mounting, right and left.Width: 10.5625 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Transmission Mount Service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission Mount Service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Trunk or Hood Bumper
p/n: 34-0203-42
This Bumper is designed to be used for the trunk or hood. The bumper is molded with clearance for the screw.
Trunk Weatherstrip
p/n: 70-0873-84
This Trunk Weatherstrip set is designed from original parts for superior fitment and seal. The weatherstrips mount directly to the body and cover the full perimeter of the trunk.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Vent Division Bar Weatherstrip
p/n: 70-2089-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Windshield Gasket
p/n: 70-0524-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Wiper control grommet
p/n: 60-0197-53
Grommet, wiper control connection link. Replaces #4161287. 11/32" I.D. X 19/32" O.D.
