Firewall Grommet
p/n: 30-0456-20
This Firewall Grommet is used for the heater core at the firewall. Designed from the original part for superior fit and seal.
Front Door Vent Window Set
p/n: 90-0331-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 30-0443-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrip
p/n: 90-0148-72
This Front Door Weatherstrip set is for the front doors. The set includes weatherstrip for door perimeter and hinge pillars.
Front Spring Bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Front Spring Bumper
p/n: 30-0119-32
Bumper, front spring compression, lower arm. Steel core, retained by clip (not included).Height: 2.625 inches.
Front Spring Upper Bumpers
p/n: 30-0516-32
This Front Spring Upper Bumper pair is a quality reproduction of the original factory part. These dense rubber bumpers mount left and right to function as the rebound bumper for the front springs.
Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Front Stabilizer Bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
Hood to Cowl Weatherstrip
p/n: 70-1296-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. Fully molded with carrot-bumper retainers.
Hood To Fender Bumper
p/n: 30-0304-42
This Hood To Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
License Lens Gasket
p/n: 70-2121-17
Gasket, rear bumper license plate lens. Machine die-cut from 1/16" rubber.Length: 6.5625 inches. Width: 1.625 inches.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Rear Shield to Bumper Seal
p/n: 30-0476-44
This Rear Shield to Bumper Seal is made of high quality EPDM dense rubber. The seal is designed from an original part so it fits correctly. Overall length is seven (7) feet.