Parking, Signal Light Lens Gaskets - Front
p/n: 50-0192-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Power Brake Pedal Pad
p/n: 50-0406-22
Pad, power brake pedal. Available in BLACK only, "Power Brake" written with white lettering.Width: 5.5 inches. Height: 2.625 inches.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter vent weatherstrip
p/n: 38-0075-76
Weatherstrip, quarter window vent. Includes division bar seals and run channel.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-0729-79
This Quarter Window U Jamb Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-0923-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Radiator bracket cushion
p/n: 50-0324-42
Bumper for bracket, radiator upper panel to grill. Use original steel bracket.Buick 1941: 1 required per car. 1942: Part not used for this year.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Rear Axle Suspension Bumper
p/n: 70-2638-35
This Rear Axle Suspension Bumper is fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Rear Door Lock Pillar Weatherstrips
p/n: 70-1907-79
This Rear Door Lock Pillar Weatherstrip pair seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Rear door vent weatherstrip
p/n: 38-0088-74
Weatherstrip, rear door vent window. Order our #70-0783-74 division post weatherstrip separately.
Rear Door weatherstrip
p/n: 90-0132-72
Rear door edge weatherstrip. This part is the primary door to body weatherstrip. Includes the perimeter seal for both rear doors and the molded corners. Set consists of four (4) pieces. Kit does not include adhesive. Includes the following components
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Rear Door Weatherstrips
p/n: 70-0571-72
A Rear Door Weatherstrip set with molded ends. This part is the primary door to body weatherstrip. Includes clips and pins for easy installation.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Rear Window Gasket
p/n: 50-0191-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 70-0579-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 70-0789-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The rear gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 70-1862-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 30-0368-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 50-0323-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.