Front Engine Support
p/n: 70-0276-11
This Front Engine Support is designed from original parts for an exact reproduction. Constructed of rubber and steel for proper engine vibration isolation.
Gravel Shield
p/n: 70-0093-45
Rear body deflector apron or valance. Original copy including fastening bolt holes. You locate exhaust hole where needed. Approximately fifty eight (58) inches long.
Front Stablizer Bar End Link Kit
p/n: 70-0574-33
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Side Deflector / Valance Rubber
p/n: 70-0092-45
This Side Deflector / Valance Rubber pair is designed from the original part for superior fitment and seal. Each deflector piece is approximately 6 feet long.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Accelerator Pedal Pad
p/n: 70-0407-40
Pad, accelerator pedal. Slipover style. Exact copy and top quality rubber.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fuel Neck Grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
License plate mounting pad
p/n: 70-0124-17
Pad, rear license bracket mounting. See our other parts #70-0174-17 and #70-0348-17 sold separately.
Brake and clutch shank seal
p/n: 70-0192-23
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
2-3/8" Firewall Grommet
p/n: 70-0350-20
This Firewall Grommet is used to run the coil wire thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Hood Rest Pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Lower suspension arm dust seal
p/n: 70-0625-32
Dust seal, lower suspension arm bushing. Four (4) required per car.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.
Rear Leaf Spring & Shackle Bushing
p/n: 70-0182-32
This Rear Leaf Spring Bushing is designed from the original part for superior fitment and function. Bushing is for the rear leaf spring front or rear spring to shackle. Two bushings pushed together form one complete bushing. May require eight (8) or twelve (12) each depending or vehicle model if replacing all bushings.
1-3/8" Firewall Grommet
p/n: 70-0712-20
This Firewall Grommet is designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability. Two (2) holes in grommet.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
2-1/4" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 70-0264-48
This Body To Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs under body mount / washer below bracket. Fully molded high quality EPDM rubber.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
1-9/16" Firewall Grommet
p/n: 32-1201-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Front Fender Dust Shield Clip
p/n: 70-0681-44
This Front Fender Dust Shield Clip is designed from spring tempered wire, to original configuration. Up to sixteen (16) per car required.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.