Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Defroster Vent Gasket
p/n: 70-2279-31
Gasket, defroster vent at base of windshield. One (1) pair required per car.
Hood to Cowl Side Extension Filler
p/n: 70-2258-43
This Hood to Cowl Side Extension Filler pair is fully molded from soft EPDM sponge rubber with all original details.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2494-45
This ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Front Suspension Bumper
p/n: 70-2649-35
This Front Suspension Bumper pair for the Lower A-arm is made from 100% EPDM dense rubber for durability. Fully molded with integral mounting bolt.
Axle Rebound Pad
p/n: 70-2591-32
Bumper, air suspension rear axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Hood To Cowl Weatherstrip
p/n: 70-1019-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Axle Rebound Pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Front Door Hinge Pillar Weatherstrips
p/n: 60-0326-73
This Front Door Hinge Pillar Weatherstrip set fits at the front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
1959-1960 Cadillac Factory Shop Manual, CD
p/n: 07-1058-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory shop repair manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Front Inner Fender Seals at Rear
p/n: 70-2786-45
This Front Inner Fender Seal pair is designed from the original part for superior fitment and seal. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear side of front inner fenders, making a Right and Left pair.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.