Window Felt and Run Channel Set
p/n: 70-2486-58
This eight (8) piece Window Felt and Run Channel Set is designed for superior fitment and function. The set contains the flexible run channels and window felt beltline weatherstrips needed for the side window glass. The set does two (2) front doors, left and right.
Front Door Weatherstrips
p/n: 60-0416-72
This Front Door Edge Weatherstrip pair is the primary door to body weatherstrip. This Original profile weatherstrip pair for 1955-2nd type pair is the OEM cross-section profile, proper length door edge seal which attaches to the door with pre-inserted plastic attaching pins.
Window Felt Beltline Weatherstrips - Vent Window Delete
p/n: 80-1106-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece set is custom made for vehicles with the vent or wing windows removed.
Front Door Vent Window Weatherstrip Set
p/n: 60-0297-55
This four (4) piece Door Vent Window Weatherstrip Set contains the main vent window and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory fit. The division post weatherstrips contain a brass core for durability and easy installation.
Windshield Gasket without Groove
p/n: 60-0289-50
This Windshield Gasket without Groove is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. For models with no reveal molding.
Windshield Gasket with Groove
p/n: 60-0379-50
This Windshield Gasket with Groove mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the groove slot to accommodate the outer edge's decorative reveal molding.
Front Door Weatherstrips
p/n: 60-0485-72
This Front Door Edge Weatherstrip pair is the primary door to body weatherstrip. This smaller for 1955-2nd type weatherstrip pair is the proper length door edge seal which attaches to the door with pre-inserted plastic attaching pins.
Rear Window Gasket Set
p/n: 60-0182-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a thirteen foot, one inch (13' 1") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Window Felt Beltline Weatherstrips
p/n: 80-0056-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece set includes inner and outer window felt beltline weatherstrips for each door side window.
Steering Column Grommet
p/n: 60-0436-32
Grommet, steering gear. Molded with metal core as original with all original features.Length: 4.375 inches.
Flexible Run Channel
p/n: 60-0375-58
For windows with metal glass frames. Flexible corrugated steel, cloth covered, mohair lined. Available in 5ft lengths.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Parking Brake Boot
p/n: 60-0145-24
This Parking Brake Boot is used for the brake lever at the floor. Designed from an original part and molded from EPDM dense rubber for durability and proper fit.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Headliner Retainer Strip
p/n: 60-0368-88
Retainer strip. Holds cardboard headliner in place. Twelve (12) foot strip.Length: 144.0 inches. Width: .5625 inches.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Vent Window Division Post Weatherstrips
p/n: 60-0663-56
This Vent Window Division Post / Bar Weatherstrip pair is fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Accelerator Pedal Pad
p/n: 60-0301-41
Pad, accelerator pedal. Slipover cover type. Exact copy. Fits original steel core. Length: 8.0 inches.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Fuel Neck Grommet
p/n: 60-0475-41
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3-1/2") outside width by three and fifteen sixteenths inch (3-15/16") outside length.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Front Fender Seal
p/n: 60-0438-45
Seal, vertical, front quarter panel (fender) to cab at rear of fender (cowl). Two (2) piece set for both sides of cab.
Brake and Clutch Pedal Pad
p/n: 60-0218-22
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Brake and Clutch Pedal Bumper
p/n: 60-0579-24
Bumper, brake or clutch pedal to floorboard. Longer type with one and three eighths (1-3/8) inch clearance for pedal shaft.Length: 2.75 inches.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Steering Column Seal
p/n: 60-0435-32
Seal, steering column at toe pan, sponge.Length: 5.375 inches. Height: .25 inches.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Rear Spring Bushing
p/n: 60-0208-32
This Rear Spring Bushing pair is designed from the original part for superior fitment and function. Bushings are for the rear spring, shackle eye, and spring eye. Up to twelve (12) per car.
Body Bolt Cushion
p/n: 60-0189-48
This Body Bolt Cushion is used for each body bolt under frame bracket, to cushion washer and nut. Fully molded from top-quality EPDM rubber with a high level of fit and finish.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Hood Side Upper Bumper
p/n: 70-2617-42
This Hood Side Upper Bumper is fully molded with top quality EPDM rubber. The authentic configuration for 1/4" hole. Six (6) bumpers typically required per vehicle.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
15/16" Firewall Grommet
p/n: 32-0162-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as ignition to starter wire through the firewall.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
3/4" Parking Brake Grommet
p/n: 32-0537-24
This Parking Brake Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the parking brake release rod.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.