Front Door Vent Window Set
p/n: 90-0452-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0022-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Spring Bumper
p/n: 60-0021-35
Rebound bumper, front spring and rear spring for beam axle cars, steel ring reinforced as original.Height: 2.4375 inches.
Handbrake Lever Anti-Rattle
p/n: 60-0531-24
Spacer, anti-rattle, handbrake lever sector rod, between release rod and handbrake lever.Width: .6875 inches. Height: .6875 inches.
Hood Front Corner Pads
p/n: 60-0052-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Hood Rear Corner Pads
p/n: 60-0053-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Rear Spare Wheel Carrier Pad
p/n: 60-0164-37
Pad, rear mounted spare wheel support. Seven (7) inch by seven (7) inch, three (3) hole pattern, brass core as original.Width: 7.0 inches. Height: 7.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Rear Window Gasket
p/n: 60-0367-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Side mount spare wheel grommet
p/n: 60-0331-37
Grommet, sidemount wheel carrier-through-fender, right and left.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Steering Column Cushion
p/n: 60-0012-36
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Taillight Mounting Pad
p/n: 60-0075-15
Pad, taillight and license bracket mounting. Two and five eighths (2-5/8) inch by four and one half (4-1/2) inch. Length: 4.5 inches. Width: 2.625 inches.
Transmission Mounting Pad
p/n: 60-0303-25
Insulator replacement set. 2-piece unit of special soft rubber to be used with original steel channel and plate.
Vent division bar weatherstrip
p/n: 60-0689-55
Front door vent window divsion bar seal. Proper cross section rubber seal bonded to metal core with authentic style mounting tabs.
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Windshield Gasket
p/n: 60-0366-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.