Body Weatherstrip Kit
p/n: 90-3037-90
This five (5) piece kit includes the major weatherstrip components needed for your restoration project.
Front Door Vent Window Weatherstrip Set
p/n: 90-0317-90
This four (4) piece Front Door Vent Window Weatherstrip Set contains the main vent window and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 27-0055-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 70-1531-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Tailgate Lower Weatherstrip
p/n: 70-2123-85
This Tailgate Lower Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate with properly spaced plastic clips.
Rear Door Weatherstrip
p/n: 82-0133-72
Rear door edge weatherstrip. This part is the primary door to body weatherstrip.
Cowl Drain Gutter
p/n: 70-0780-73
Gutter, windshield lower corner, left and right. Rubber with metal core as original. Seven and three quarters long (7-3/4").Length: 7.75 inches.
Front Door Weatherstrips
p/n: 70-2143-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. This part is the primary door to body weatherstrip which mounts directly to the door to seal against the body when closed.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Tailgate Weatherstrip Filler
p/n: 70-2056-87
Filler, tailgate weatherstrip at beltline, on body. Fully molded with holes for attaching pins.Length: 4.0 inches.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent division bar weatherstrip
p/n: 70-1533-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Transmission Mount Service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Splash Apron / A-Arm Dust Shield
p/n: 70-2801-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.