Headlight Mounting Pad
p/n: 60-0163-14
Pad, headlight bracket mounting right and left. One and seven eighths (1-7/8) inch by two and seven eighths (2-7/8) inch overall.Length: 2.875 inches.
Hood Corner Pad
p/n: 60-0006-42
Pad, hood, rear corner. Brass core and tabs, excellent copy. In 1935: Two (2) are used per car. In 1936: Four (4) are used per car.
Hood Corner Pad
p/n: 60-0399-42
Bumpers, hood front corners. Right and Left with metal cores.Width: 1.625 inches.
Hood Rear Corner Pads
p/n: 60-0053-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Weatherstrips
p/n: 60-0282-77
This Quarter Window Weatherstrip pair is designed from the original part for superior fitment and seal. This channel weatherstrip mounts around the full perimeter of the quarter glass for a precise, factory fit. For stationary windows only.
Quarter Window Weatherstrips
p/n: 27-0040-77
This Quarter Window Weatherstrips pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the quarter glass for a precise, factory fit. For fixed, stationary windows only.
Rear Bumper Grommet
p/n: 60-0061-28
Grommets, rear bumper, right and left, for round bumper support bracket; left hand grommet has clearance for electrical conduit.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Rear Spare Wheel Carrier Pad
p/n: 60-0164-37
Pad, rear mounted spare wheel support. Seven (7) inch by seven (7) inch, three (3) hole pattern, brass core as original.Width: 7.0 inches. Height: 7.
Rear Spring Bumpers
p/n: 60-0179-35
This Rear Spring Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Mounts to the frame for the rear springs. An assembly with rubber vulcanized to steel as original.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Rear Window Gasket
p/n: 70-0687-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0433-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0330-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0367-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumble Seat Step Pad
p/n: 60-0501-45
Step pad, rumble seat, on rear fender, with bowtie emblem. Steel core with bolt.Width: 4.375 inches. Height: 5.25 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Weatherstrip
p/n: 25-0025-85
This Rumble Seat Weatherstrip set is designed from original parts for superior fitment and seal. The set contains the pieces for the lower edge and corners.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
Taillight Mounting Pad
p/n: 60-0172-15
Pad, taillight bracket mounting. Five and one half (5-1/2) inches long. Compare with our #60-0116-15. Length: 5.50 inches.
Taillight Mounting Pad
p/n: 60-0364-15
Pad, taillight mounting to rear fender. Length: 1.0625 inches.
Taillight Mounting Pad
p/n: 60-0116-15
Pad, taillight bracket to fender. Four (4) inches long. Compare with our #60-0172-15 and #60-0545-15. Length: 4.0 inches.
Transmission Mount - Revulcanization Service Only
p/n: 60-0627-25
This Transmission Mount - Revulcanization Service Only is designed to restore your transmission mount to a like new original condition. Please call or email for more service details and ordering.
Transmission Mount Service
p/n: 60-0309-25
Insulator (support) engine at transmission. Revulcanization service only.Length: 7.9375 inches.
Transmission Mounting Pad
p/n: 60-0303-25
Insulator replacement set. 2-piece unit of special soft rubber to be used with original steel channel and plate.
Trunk Weatherstrip
p/n: 70-1128-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Trunk Weatherstrip
p/n: 70-0797-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Vent division bar weatherstrip
p/n: 60-0689-55
Front door vent window divsion bar seal. Proper cross section rubber seal bonded to metal core with authentic style mounting tabs.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Window Felt and Run Channel Set
p/n: 90-0142-58
This six (6) piece Window Felt and Run Channel set includes the inner and outer window felts and the flexible run channels needed to complete two (2) doors. This set is used for front or rear doors in models without vent windows in the door.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Windshield Gasket
p/n: 50-0530-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Windshield Gasket
p/n: 60-0366-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket
p/n: 60-0432-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Mounting Pad
p/n: 60-0360-52
Pad, windshield lower weatherstrip, retainer-to-cowl.Length: 44.0 inches. Width: 1.5625 inches.
Windshield mounting pad
p/n: 60-0362-52
Pad, windshield side arm-to-cowl, right and left. Replaces #370356.
Windshield Weatherstrip
p/n: 60-0004-52
This Windshield Weatherstrip is made of a high-quality EPDM dense rubber extrusion. The four (4) foot strip mounts on the lower windshield for easy installation.
Windshield Wiper Transmission Gaskets
p/n: 70-1196-53
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.