Fender Brace To Fender Support Rubber
p/n: 20-0491-45
This Fender Brace To Fender Support Rubber pair is designed from the original part for superior fitment and function. These rubber isolators work to reduce metal to metal noise and vibration.
Fuel Tank Support Pad
p/n: 20-0425-41
This Fuel Tank Support Pad pair installs between the fuel tank and floor to reduce noise. Designed from original specifications so it fits correctly.
Steering Column Floorplate
p/n: 20-0449-88
Seal, brake, clutch and steering column to floor. Column shift models. Installs under metal plate at floor.
Vent Division Bar Weatherstrips
p/n: 20-0469-56
This Front Vent Division Bar Weatherstrip pair is an extruded rubber strip only that will have to be attached to division post. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Engine Mount Bolt
p/n: 20-0309-11
This Engine Mount Bolt can be used for the front or rear. Hex head bolt drilled for cotter key.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Door Handle Gaskets
p/n: 20-0478-69
This two (2) piece Outside Door Handle Gasket pair is designed from the original part for superior fitment and seal. Gaskets have a proper raised edge to center the handle on so it fits correctly.
Clutch and Brake Pedal Arm Bumpers
p/n: 20-0448-24
This Clutch and Brake Pedal Arm Bumper pair is designed from the original part for superior fitment and function. Bumpers mount on the underside of the truck floor pan.
Taillight Lens Gasket
p/n: 20-1988-15
Gasket, taillight lens. Inner and outer seal. Enough for one taillight lens.
Radiator Splash Shield
p/n: 20-0484-45
This Radiator Splash Shield is designed from the original part for superior fitment and proper seal. Lower radiator grille (splash pan) to radiator seal.
Speedometer Housing Grommet
p/n: 20-0447-20
This Speedometer Housing Grommet is used where the cable runs through the floorboard. Also allows for the choke and throttle cable to go through the firewall.
Steering Column Floorplate
p/n: 20-0450-88
Seal, brake, clutch and steering column to floor. Floor shift models.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Door Jamb Bumper
p/n: 20-2109-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Body Mounting Pad
p/n: 20-0458-48
Bushings, rear of cab to frame suspension arm. Set of four (4) pieces.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
License Plate Light Lens to Housing Gasket
p/n: 20-0489-17
This License Plate Light Lens To Housing Gasket is designed from the original part for superior fitment and seal. This die cut cork reproduction gasket fits between the between lens and housing for the license plate light.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Engine Mount Washer
p/n: 20-0440-11
This Upper Engine Mount Washer is made of steel. Reproduction is designed from the original part to fit correctly.