Body Weatherstrip Kit
p/n: 90-3130-90
This five (5) piece Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for your restoration project.
Rear Window Gasket
p/n: 70-0826-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Front Door Vent Window Weatherstrip Set
p/n: 90-0414-90
This four (4) piece Front Door Vent Window Weatherstrip Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Prop shaft support service
p/n: 27-0099-27
Support, propeller shaft center bearing. Revulcanization service only.
Windshield Gasket
p/n: 70-0671-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0077-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrips
p/n: 70-1536-72
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. These primary front door weatherstrips mount (push pin) to seal the driver and passenger doors when closed.
Cowl Drain Gutter
p/n: 70-0867-73
Gutter, cowl side drain, left and right. Rubber with metal core as original. Eleven (11") inches long.Length: 11.0 inches.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Front Door Hinge Pillar Weatherstrips
p/n: 60-0326-73
This Front Door Hinge Pillar Weatherstrip set fits at the front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Vent Window Division Bar Weatherstrips
p/n: 50-0332-56
This Front Vent Window Division Bar / Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar and seals as the vent glass closes against it.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Body Bolt Cushion
p/n: 27-0079-48
Pad, body bolt insulator. Metal core & locating collar covered with rubber. Number used varies per car. Two inch (2") square by seven eights inch (7/8") locating collar outside diameter by five eighths (5/8") locating collar inside hole diameter. Five eig
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Folding Seat Back Frame Bumper
p/n: 70-2579-88
A Folding Front Seat Frame Rest Cushion Bumper manufactured from dense rubber with a molded in metal retaining washer. Two (2) used per vehicle.
Glovebox Door Check Grommet
p/n: 27-0105-88
This Glovebox Door Check Grommet is manufactured out of 100% EPDM dense rubber for durability. Designed from original for a proper fit.
Hood Bumper
p/n: 27-0098-42
Bumper, hood front to radiator ledge, adjustable. Includes plated bolt and rubber cushion.Length: 2.1875 inches.
Door Handle Gasket Set
p/n: 27-0102-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Body Bolt Cushion
p/n: 60-0189-48
This Body Bolt Cushion is used for each body bolt under frame bracket, to cushion washer and nut. Fully molded from top-quality EPDM rubber with a high level of fit and finish.
Hood Bumper
p/n: 27-0103-42
Bumper, hood to fender ledge. Uses four (4) per car.Width: 1.25 inches. Height: .9375 inches.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1" Floor Pan Plug
p/n: 35-0262-20
This Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to twelve (12) used per vehicle.
5/8" Gearshift Bushing
p/n: 32-0051-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift selector rod.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Clip Fastener - Door Weatherstrip
p/n: 60-0260-73
This Clip Fastener for Door Weatherstrips is made for a precise, factory like fit. Two (2) prong clip fastener with oval screw hole, made with spring steel and cadmium plated. Width: 7/8" inches. Height: 15/16 inches.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
7/8" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Weatherstrip Fastener
p/n: 50-0198-73
This Door Weatherstrip Fastener is steel with a black finish. Each push-in fastener measures one half (1/2") inch long with a thirteen thirty second (13/32") inch diameter head. Reproduction fastener is designed from the original part to fit correctly.
Door Bumper
p/n: 33-1233-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1232-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1235-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.