Side Mount Grommets
p/n: 30-0079-37
This reproduction Side Mount Grommet pair is designed from the original part for an authentic fit, finish, and appearance. This is the side mount brace, lower, to fender grommet.
Fuel Neck Grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3-3/8") outside width by three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter by one and one fourth inch (1-1/4") height.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Air Conditioning Pipe Grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Fuel Neck Grommet
p/n: 40-0272-39
Grommet, fuel filler neck. Oblong shape, fully molded rubber. Four and one fourth inch (4-1/4") outside width by five and five eighths inch (5-5/8") outside length by seven eighths (7/8") height.
Firewall Pass Through Grommet
p/n: 50-0084-20
This Firewall Pass Through Grommet is designed as a five (5) hole pass-thru from the original part for superior fit and seal. Sold as a two (2) set for the inner and outer side.
Headlight grommet
p/n: 25-0039-14
Base, headlight wire conduit and support post. (Vertical post under headlight).
Firewall Grommet
p/n: 18-0015-20
This Firewall Grommet is designed to pass the cables and wires through the firewall. The seven (7) hole is for all 1937 models; fits retainer and can be altered into eight (8) hole type for all 1936 models.
Fuel Neck Grommet
p/n: 70-0404-39
Grommet, fuel filler neck. Fully molded rubber. Flat bottom has slight ridge (seam) along edge. Four and three eighths inch (4-3/8") outside diameter by two and three sixteenths inch (2-3/16") inside hole diameter by five eighths inch (5/8") height.
Body Plug - Rubber Grommet Set
p/n: 20-2705-20
This fourty-four (44) piece Body Plug and Grommet set is designed from the original parts for superior fitment and sealing. Mustang Club of America (MCA) approved.
Steering Column Grommet
p/n: 40-0007-36
This Steering Column to Toe Board Grommet is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column through the body floor pan. For one and one half (1-1/2) inch steering column tube.
Steering Column Grommet - Black
p/n: 40-0144-36
This molded Steering Column to Toe Board Grommet is designed from the original part for superior fitment and function. This black rubber part seals around the steering column at the toe board on the interior side.
Fuel Neck Grommet
p/n: 50-0067-39
Grommet, fuel filler neck. Oblong fully molded rubber. Two and one eighths inch (2-1/8") inch inside length by three and one half inch (3-1/2") outside diameter by three and three fourths inch (3-3/4") outside length.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Firewall Pass Through Grommet
p/n: 40-0522-21
This Firewall Pass Through Grommet is the rectangular large type. Designed from the original part for superior fit and seal.
Fuel Filler Neck Bezel Mounting Pad
p/n: 16-0001-41
A Fuel Filler Neck Bezel Mounting Pad. Good copy of the original. Length: 5-3/4 inches.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Side Mount Grommet
p/n: 30-0100-37
Grommets, spare wheel sidemount brace, lower.Length: 2.625 inches. Width: 2.50 inches.
Side Mount Grommet
p/n: 40-0269-37
Grommet, spare wheel sidemount main support tube. Covers hole in fender, one per vehicle.Length: 4.875 inches.
Steering Column Grommet - Black
p/n: 40-0078-36
This molded Steering Column to Toe Board Grommet is designed from the original part for superior fitment and function. This black rubber part seals around the steering column at the toe board on the interior side.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Fuel Neck Grommet
p/n: 40-0099-39
Grommet, fuel filler neck. Fully molded rubber. Four and five sixteenths inch (4-5/16") outside diameter by two and three sixteenths (2-3/16") inside diameter by three eighths inch (3/8") height.
Steering Column Grommet
p/n: 70-0349-88
This Steering Column at Floorboard Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality EPDM rubber to authentic original dimensions. This part fits around the steering column to seal the column at the body floorboard.
2-13/16" Firewall Grommet
p/n: 70-0644-20
This Firewall Grommet is used to run dash wires through the firewall. Designed from the original part for superior fit and seal.
2-13/16" Firewall Grommet
p/n: 70-0447-20
This Firewall Grommet is designed to be used for the main wiring harness and miscellaneous wires through the firewall. (The main cable and up to eight (8) other wires, tubes or cables.)
2-7/8" Firewall Grommet
p/n: 70-1747-20
This Firewall Grommet is used to pass the dash wires through the firewall. Designed from the original part for superior fit and seal.
Battery Cable Grommet
p/n: 70-2318-20
Grommet, battery cable through radiator shroud. Reproduction of original rectangular design exactly. Replaces #1469080. Length: 2.4375 inches. Width: 1.5 inches.
Body Plug - Rubber Grommet Set
p/n: 20-2704-20
This thirty-eight (38) piece Body Plug and Grommet set is designed from the original parts for superior fitment and sealing. Mustang Club of America (MCA) approved.
Fuel Neck Grommet
p/n: 20-2010-39
This Fuel Neck Grommet is manufactured of a top quality material and dimensionally correct for a factory look and fit.
Fuel Neck Grommet
p/n: 10-0120-41
Grommet, fuel filler neck. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by two and five eighths inch (2-5/8") inside diameter by thirteen sixteenths inch (13/16") height.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Fuel Neck Grommet
p/n: 40-0139-39
Grommet, fuel filler neck. Fully molded rubber, slightly angled. Four and one half inch (4-1/2") outside width by four and five eighths inch (4-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter.
Fuel Neck Grommet
p/n: 12-0001-39
Grommet, fuel filler neck. Fully molded rubber. Three and three fourths inch (3-3/4") outside diameter by one and seven eighths inch (1-7/8") inside diameter by three inch (3") sheet metal opening.
Side Mount Spare Wheel Grommet
p/n: 70-0099-37
Grommets, spare wheel sidemount arm.Width: 3.625 inches.
Fuel Neck Grommet
p/n: 40-0352-39
Grommet, fuel filler neck, exact copy with thirty (30) degree slope. Fully molded rubber with retaining flange. Three and five sixteenths inch (3-5/16") outside width by four and one eight inch (4-1/8") outside length.
Fuel Neck Grommet
p/n: 40-0286-39
Grommet, fuel filler neck. Fully molded rubber. Three and one fourth inch (3-1/4") outside diameter by two and one half inch (2-1/2") inside diameter by five eighths inch (5/8") height. Also see our #40-0043-39 sold separately.
Firewall Grommet
p/n: 70-0950-20
This Firewall Grommet is for the windshield washer line, antenna vacuum line, and (convertibles only) folding top control rod through firewall.
Division bar grommet
p/n: 70-3135-62
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Firewall Grommet
p/n: 17-0045-20
This Firewall Grommet is designed as a firewall pass through for eight (8) wires or cables. For twelve (12) cylinder models only. For eight (8) cylinder models see our 17-0044-20.
Fuel Neck Grommet
p/n: 60-0543-41
Seal, gas tank filler tube through floor pan, to inside of body. Made of soft flexible durometer rubber. Four and seven sixteenths inch (4-7/16") outside width by five and five eights inch (5-5/8") outside length.
Steering Column Grommet
p/n: 70-0450-88
This Steering Column at Floor Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality EPDM rubber to authentic original dimensions. Fits to chrome ring.
Body Plug - Rubber Grommet Set
p/n: 20-2703-20
This thirty-three (33) piece Body Plug and Grommet set is designed from the original parts for superior fitment and sealing. Mustang Club of America (MCA) approved.
Brake and clutch shank seal
p/n: 70-0192-23
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Firewall Grommet
p/n: 25-0026-20
This Firewall Grommet is the six (6) hole type used to run wires, cables, or tubes through the firewall. Designed from the original part for superior fit and seal.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Gearshift Boot
p/n: 30-0412-24
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Steering Column Grommet
p/n: 30-0106-36
This Steering Column to Toe Board Grommet is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column through the body floor pan.
Fuel Filler Neck Grommet
p/n: 20-1848-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. The part is fully molded rubber in soft flexible rubber.
Fuel Neck Grommet
p/n: 20-1849-39
Grommet, fuel filler neck. Outside diameter: 3-3/8" Inside diameter: 2"
Fuel Neck Grommet
p/n: 60-0181-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and seven sixteenths inch (3-7/16") outside width by three and five eights inch (3-5/8") outside length.
Fuel Neck Grommet
p/n: 20-1848-108
This Fuel Neck Grommet is made from high-quality EPDM dense rubber for the Builder’s application use and creativity. The part is fully molded rubber. Excellent for use in many applications.
Steering Column Grommet
p/n: 60-0341-32
This Steering Column at Floor Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality EPDM rubber to authentic original dimensions. This part fits around the steering column to seal the column at the body floor pan.
Steering Column Grommet - Brown
p/n: 27-0047-89
This molded Steering Column to Toe Board Grommet is designed from the original part for superior fitment and function. This brown rubber part seals around the steering column at the toe board on the interior side.
Firewall Grommet
p/n: 70-0949-20
This Firewall Grommet is used to run the heater lines to the control valve. Designed from the original part for superior fit and seal.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fuel Filler Neck Grommet
p/n: 50-0245-39
This reproduction Fuel Filler Neck Grommet is designed from the original part for an authentic fit, finish and function. Grommet is made from high-quality EPDM dense rubber.
Fuel Neck Grommet
p/n: 50-0245-108
This Fuel Neck Filler Grommet is made from high-quality EPDM dense rubber for the Builder’s application use and creativity. The part is fully molded rubber. Excellent for use in many applications.
Steering Column Grommet - Brown
p/n: 60-0102-89
This molded Steering Column at Floorboard Grommet is designed from the original part for superior fitment and function. This brown rubber part seals around the steering column at the floorboard on the interior side. For column shift models.
Rubber Grommet Assortment Set
p/n: 70-4728-20
A ninety-nine (99) piece Rubber Grommet Assortment Set with popular size coverage in a convenient and economic package. Assortment comes in a convenient, translucent, durable polypropylene box.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Front Bumper Seal
p/n: 70-1103-28
Seals, front bumper. Fully molded rubber, U-shaped. Three and one half inches (3-1/2") long by three and one half inches (3-1/2") wide by thirteen sixteenths inch (13/16") height. For the grommets see our #70-1104-28, sold separately.
Heater control valve seal
p/n: 50-0347-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Hydraulic Pump Grommet
p/n: 70-0640-21
Grommet, two (2) hole, for hydraulic pump through sheet metal.Length: 1.9375 inches. Width: 1.125 inches.
Steering Column Grommet
p/n: 40-0237-36
This Steering Column Grommet is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column at the floorboard or firewall opening.
Fuel Neck Grommet
p/n: 20-0581-39
Grommet, gas tank neck. Oval shaped. Fully molded rubber with retaining flange. Three and thirteen sixteenth inch (3-13/16") outside width by four and five sixteenths inch (4-5/16") outside length.
Fuel Tank Filler Neck Grommet - Panel Truck
p/n: 20-0486-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck at the vehicle body panel.
Firewall Wiring Grommet
p/n: 25-0016-20
This Firewall Wiring Organizer Grommet is designed for original configuration and superior fit. Made from high-quality dense rubber to provide excellent durability.
Horn Button Contact Ring Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact Ring Set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blow ring.
Accelerator Rod Seal
p/n: 60-0086-40
Grommet, accelerator rod through toe board. Brass core as original.
Body Plug - Rubber Grommet Set
p/n: 20-2702-20
This thirty-two (32) piece Body Plug and Grommet set is designed from the original parts for superior fitment and sealing. Mustang Club of America (MCA) approved.
Firewall Grommet
p/n: 30-0456-20
This Firewall Grommet is used for the heater core at the firewall. Designed from the original part for superior fit and seal.
Headlight Grommet
p/n: 70-0254-14
Grommets, radiator shell headlight crossbar braceHeight: .3125 inches.
Rear Bumper Arm Grommets
p/n: 20-2170-29
This Rear Bumper Arm Grommet pair is designed from the original part for an authentic fit, finish, and appearance.
Steering Column Grommet
p/n: 70-0283-88
This Steering Column at Floor Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality EPDM rubber to authentic original dimensions. This part fits around the steering column to seal the column at the body floor pan.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Division Bar Grommet
p/n: 70-0272-62
Grommets, rear door vent divider post, top and bottom, right and left.
1-1/4" Firewall Grommet
p/n: 30-0060-21
This Firewall Grommet is used to run the coil wire and temperature gauge line through the firewall. Designed from the original part for superior fit and seal.
2" Firewall Grommet
p/n: 70-1725-20
This Firewall Grommet is used to run the windshield washer hose and antenna wiring through the firewall. Designed from the original part for superior fit and seal.
2" Wiring Harness Firewall Grommet
p/n: 70-1724-20
This Wiring Harness Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
2-5/8" Firewall Grommet
p/n: 70-1628-20
This Firewall Grommet is used for the wiring harness. Designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability.
Firewall Grommet
p/n: 70-0554-20
This Firewall Grommet is a special rectangular, two (2) hole grommet, that is used on the left side of the cowl the run the hydraulic line through the sheet metal.
Firewall Grommet Set
p/n: 20-1997-20
This Firewall Grommet Set contains eleven (11) pieces including drain tube, plugs and grommets for the firewall. Designed from the original part for superior fit and seal.
Fuel Neck Grommet
p/n: 60-0336-41
Grommet, fuel filler neck. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside diameter by two and one sixteenth inch (2-1/6") top hole diameter by two and three sixteenths inch (2-3/16") bottom hole diameter.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.