Firewall Grommet
p/n: 27-0026-20
This Firewall Grommet is used to run the control cables, tubes, and wires through the firewall. The two (2) hole type fits a three fourths (3/4) inch by one and five sixteenths (1-5/16) inch hole.
4-Port Firewall Grommet
p/n: 60-0276-45
This four (4) port Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Cowl Wiring Firewall Grommet
p/n: 20-1560-20
This Cowl Wiring Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Emergency Brake Cable Grommet
p/n: 20-2299-20
This Emergency Brake Cable Grommet is used for running the emergency brake cable and the speedometer cable through the firewall. Made from high-quality dense rubber to provide excellent durability.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
1-5/8" Firewall Grommet
p/n: 50-0364-20
This Firewall Grommet is used to run the oil pressure and water temperature, or washer vacuum hose through the firewall. Designed from original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 50-0363-20
This Firewall Grommet is used to run the windshield washer hose through the firewall. Designed from original part for excellent workmanship.
Air ventilator seal
p/n: 20-2967-31
Grommet, air ventilator duct cable to firewall.Qty Required:2 Two (2) required per car.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Wiring Harness Loom Grommet
p/n: 60-0255-14
This Grommet is designed from the original part for superior fitment. The grommet ideally works for the headlight or taillight wiring loom through body sheet metal. Four (4) to six (6) grommets per vehicle.
Battery Cable Grommet
p/n: 40-0333-21
Grommet, battery hot cable through frame. Three fourths (3/4) inch inside diameter for one and three sixteenths (1-3/16) inch hole through frame.
Parking Light Wiring Harness Grommets
p/n: 60-0452-17
This reproduction Parking Light Wiring Harness Grommet pair is designed from the original part for an authentic fit, finish and appearance. These two (2) grommets are for the parking light wiring harness through fender connection.
Front Bumper Grommet
p/n: 20-2507-45
Grommets, front stone deflector to bumper arm anti-rattler. Four and one half (4-1/2) inch long. Two (2) piece set.
Front Bumper Grommet
p/n: 20-2506-45
Grommets, front stone deflector to bumper arm anti-rattler. Two and one fourth (2-1/4) inch long.
Shift Lever Grommet
p/n: 70-0769-26
This Shift Lever Grommet fits to the upper shift lever at the steering column. It is designed from the original part for superior fitment and function.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Choke and Throttle Rod Grommet
p/n: 20-2279-88
This Choke and Throttle Rod Grommet is used where the choke and throttle pass through the dash. Designed from the original part for superior fit and seal.
1-5/16" Firewall Grommet
p/n: 32-0196-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1-11/16" Main Harness Firewall Grommet
p/n: 70-2606-20
This Firewall Grommet fits to the engine firewall where main wire harness plugs in. Designed from the original part for superior fitment and finish.
1-3/8" Firewall Grommet
p/n: 70-0712-20
This Firewall Grommet is designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability. Two (2) holes in grommet.
7/8" Firewall Grommet
p/n: 32-0394-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Door Sill Mat Retainer Grommet
p/n: 40-0125-49
This Door Sill Mat Retainer Grommet is designed from the original part for superior fitment and function. Fits at the lower door opening. For sill plates with metal stud retainer.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
1" Firewall Grommet
p/n: 32-0347-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wiper control cable and heat tube.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
Firewall Grommet
p/n: 70-2600-20
This Firewall Grommet is used to prevent chaffing or wiring, hoses, or cables that pass through the firewall, door, or trunk. Designed from original part for excellent workmanship.
Wiper control grommet
p/n: 20-2526-53
Gaskets, wiper pivot spacer to body. Replaces factory #8A-17541-B.
Overdrive Cable Grommet
p/n: 20-1812-20
This Overdrive Cable Grommet is used to help protect the overdrive pull cable when passing through the sheet metal of the firewall.
Fuel Tank Vapor Valve Grommet
p/n: 70-5008-41
Made from fuel resistant rubber this Fuel Tank Vapor Valve Grommet seals the Fuel Vapor Valve to the fuel tank.
1-1/16" Spare Wheel Carrier Grommet
p/n: 32-0253-37
This Spare Wheel Carrier Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for spare wheel carrier mounting bracket.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
Engine Valve Cover Grommet
p/n: 20-2695-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
1" Firewall Grommet
p/n: 32-1215-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wire, cable, tubes, etc, in the firewall.
1-1/2" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Front Bumper Grommet
p/n: 20-2509-45
Grommets, front stone deflector to bumper arm anti-rattler. Two and one fourth (2-1/4) inch long. Two (2) piece set.
Main Wiring Loom Grommet
p/n: 20-2433-20
This Main Wiring Loom Grommet is used to protect the wiring from the sheet metal of the firewall. Made from high-quality dense rubber to provide excellent durability.
Radiator Mounting Pad
p/n: 30-0469-31
Pad (or Grommet), radiator to dash tie rod. Die cut from one fourth (1/4) inch rubber. Four (4) used per car.Height: .25 inches.
Stabilizer Grommet
p/n: 30-0406-33
Pad, stabilizer link assembly, front, in upper end at link. Four (4) used per car. Fully molded rubber. One inch (1") outside diameter by three sixteenths inch (3/16") inside hole diameter by three fourths inch (3/4") height.
A/C Hose Firewall Grommet
p/n: 20-2721-31
This A/C Hose Firewall Grommet is used to run the hoses through the firewall. Can be used with reproduction hoses. The grommet has larger holes than original.
Parking Light Grommet
p/n: 70-0679-16
Grommet, parking light. Taillight body for wiring connectors. Hose section not furnished.Height: 1.0 inches.
Shift Lever Grommet
p/n: 50-0284-24
This Shift Lever Grommet is designed from the original part for superior fitment and usage. Ensures smooth gear changes and precise dashboard indicator alignment.
Wiper Connection Link Grommet
p/n: 60-0197-53
This reproduction 11/32" I.D. X 19/32" O.D. Wiper Connection Link Grommet is designed from the original part for an authentic fit, finish and function.
1-1/8" Firewall Grommet
p/n: 32-0226-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the handbrake cable.
1-3/8" Firewall Grommet
p/n: 32-0333-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as ignition cable and temperature gauge.
29/32" Side Mount Grommet
p/n: 32-0364-37
This Side Mount Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for side tire carrier support arm bracket.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
1-1/2" Spare Wheel Carrier Grommet
p/n: 32-0040-37
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for side mount wheels at running board apron.
A/C Hose Firewall Grommet
p/n: 20-2720-31
This A/C Hose Firewall Grommet is used when running the air conditioner hoses through the firewall. Used with original style hoses.
Door Handle Grommet
p/n: 70-0009-108
Grommet for door handle ferrule. Molded rubber with cloth covering. Excellent for use in many applications.
Emergency Brake Cable Grommet
p/n: 20-2310-24
This Emergency Brake Cable Grommet is used when running the brake cable to the frame. Made from high-quality dense rubber to provide excellent durability.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
1-3/32" Firewall Grommet
p/n: 32-1201-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Speedometer Cable Grommet
p/n: 20-0435-41
This Speedometer Cable Grommet is generally used where the speedometer cable goes through the sheet metal of the firewall. Designed from the original part for superior fit and seal.
1-1/4" Side Mount Grommet
p/n: 32-0421-37
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for side mount arm bracket.
Door Lock Button Grommet
p/n: 20-2589-108
Door lock buttons and gaskets to garnish molding for the builder’s creative application and use.
Headlight grommet
p/n: 20-1987-14
Grommets, radiator shell. Headlight wire conduits pass through these.
Speedometer Housing Grommet
p/n: 20-0447-20
This Speedometer Housing Grommet is used where the cable runs through the floorboard. Also allows for the choke and throttle cable to go through the firewall.
1-5/16" Firewall Grommet
p/n: 50-0532-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from original part for excellent workmanship.
1-5/32" Headlight Grommet
p/n: 32-0062-14
This Headlight Grommet pair is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for headlight conduits.
Engine Valve Cover Grommet
p/n: 20-2697-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Windshield Wiper Arm Grommet
p/n: 20-1612-53
This reproduction Windshield Wiper Arm to Motor Grommet is designed from the original part for an authentic fit, finish and function. Replace worn and deteriorated original wiper grommet with this direct fit like OEM reproduction.
1" Wiring Grommet
p/n: 32-0464-15
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1-1/4" Firewall Grommet
p/n: 32-0220-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as for the overdrive cable.
1-3/8" Firewall Grommet
p/n: 32-0062-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as getting the switch and coil wire through the firewall.
1-1/16" Firewall Grommet
p/n: 70-1771-20
This Firewall Grommet used to run the speedometer cable through the firewall. The grommet can also be used to run the trunk lid release cable through the rear compartment.
1-5/16" Headlight Grommet
p/n: 32-0023-14
This Headlight Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for headlight bar support.
Horn Bell To Bracket Grommets
p/n: 20-1562-21
This reproduction Horn Bell To Bracket Grommet pair is designed from the original part for an authentic fit, finish and appearance. Replace worn and deteriorated original grommets with this direct fit like OEM reproduction.
1-1/16" Firewall Grommet
p/n: 25-0098-20
This Firewall Grommet is used to run the oil pressure gauge line through the firewall. Designed from original part for excellent workmanship.
1-5/16" Headlight Grommet
p/n: 32-0063-14
This Headlight Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed to run the headlight wire conduit through the radiator shell.
7/8" Firewall Grommet
p/n: 32-1961-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Stabilizer Bar End Link or Shock Absorber Grommet
p/n: 70-0737-33
This Stabilizer Bar End Link or Shock Absorber Grommet is designed from the original part for superior fitment and usage. Fully molded quality EPDM rubber.
Emergency Brake and Speedometer Cable Grommet
p/n: 20-1565-24
This reproduction Emergency Brake and Speedometer Cable Grommet is designed from the original part for an authentic fit, appearance and function.
1-5/16" Headlight Grommet
p/n: 32-0455-14
This Headlight Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed to run the headlight wire through the wheel housing.
9/16" Battery Strap Grommet
p/n: 32-0491-21
This Battery Strap Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the battery retaining hold-down bolt.
Shock Absorber Mounting Bushing
p/n: 60-0235-33
This Shock Absorber Bushing is fully molded and designed from the original part for superior fitment and durability. A plain cylinder type bushing with flat ends for shock absorber mounting.
1-1/4" Firewall Grommet
p/n: 32-0422-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the speedometer cable through the firewall.
Speedometer Cable Grommet
p/n: 20-2435-20
This Speedometer Cable Grommet is used to protect the cable when running it through the firewall. Designed from the original part for superior fit and seal.
Windshield Wiper Hose Grommet
p/n: 20-0546-20
This Windshield Wiper Hose Grommet is used as a guard to run the wiper hose through the firewall. Made from top quality rubber to ensure durability and proper fitment.
Wiper control grommet
p/n: 20-2525-53
Gaskets, wiper pivot spacer to body. Replaces factory #8A-17541-A.
Wiper Hose Grommet
p/n: 20-2524-53
This Wiper Hose Grommet is used to protect the wire when running it through the firewall. Designed from the original part for superior fit and seal.
1" Firewall Grommet
p/n: 32-0320-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the wiring through the front body brace, right and left.