Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Gearshift Floorplate
p/n: 40-0146-88
Floorplate, gearshift and handbrake. Perfect reproduction, including brass core.Length: 8.0 inches. Width: 7.25 inches.
Gearshift Floorplate
p/n: 40-0362-88
Draft pad or plate, gearshift and handbrake. Brass core as original.Length: 10.25 inches. Width: 7.0 inches.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Handbrake Floorplate
p/n: 11-0005-24
Floor plate, handbrake lever. Brass core as original, fully detailed.
Headlight Bar Grommet
p/n: 11-0002-14
Grommet, headlight bar-to-radiator shell. Includes clearance groove, faithful detail. 1-1/8 inch inside diameter.
Headlight Bracket Pad
p/n: 50-0222-14
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Headlight grommet
p/n: 25-0039-14
Base, headlight wire conduit and support post. (Vertical post under headlight).
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Hood Bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Hood Latch Swivel Pad
p/n: 34-0408-42
Pad, hood latch swivel for hood latch pressure against hood corners. For screw or rivet.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
LaSalle Monogram
p/n: 70-0056-49
LaSalle monograms for center of running board matting, exact copy, to be in-laid.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Muffler Bypass Floor Plate
p/n: 11-0006-88
Floor plate, muffler bypass control. Brass core as original, fully detailed.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Radiator Brace Filler Strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Rear Engine Support Pad
p/n: 70-0443-11
This Rear Engine Support Pad is used as a cushion at transmission. Makes a four (4) piece set after splitting.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
Rumble Seat Step Pad
p/n: 40-0124-44
Pad, rumble seat step, with "Dodge" logo, slip over type to fit old steel core. Perfect detail and lettering.Height: .50 inches.
Rumble Seat Step Pad
p/n: 40-0012-44
Pad, rumble seat step bears Chrysler medallion logo in center.Height: .50 inches.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Rumble Seat Step Pad
p/n: 11-0012-87
Cover, rumble seat step pad, slipover type, excellent copy.Width: 5.0 inches. Height: 5.0 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Step Pad
p/n: 40-0209-44
Pad, rumble seat step slip over style for original core, "DB" logo.
Rumble Seat Step Pad
p/n: 40-0353-44
Pad, rumble seat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Rumble Seat Weatherstrip
p/n: 70-0166-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Running Board Matting
p/n: 11-0003-49
Edge panel, running board. Exact copy including 1/4 inch mounting studs. A perfect replica in highest quality material. 43-1/2 inch long.
Running Board Matting
p/n: 70-0420-49
Running board matting. Fully molded rubber strips with full length steel cores molded in.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Arm Bushing
p/n: 15-0005-33
Bushing, shock absorber arm ball joint.Height: .875 inches.
Shock Absorber Bushing
p/n: 40-0273-32
Bushing. shock absorber link, smaller type. Eight (8) required per car. Compare with our #40-0069-32 (larger type). Length: .9375 inches.
Shock Absorber Bushing
p/n: 40-0069-32
Bushing, shock absorber link, flanged at both ends. Seven eighths (7/8) inch long between flanges, one (1) inch diameter barrel.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Spare Grommet Set
p/n: 70-1136-37
This six (6) piece Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Side Mount Spare Grommet Set
p/n: 70-1134-37
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Side Roof Rail Weatherstrip
p/n: 70-0060-65
Weatherstrip, side roof rail. Made from dense rubber extrusion. Available by the foot.
Side Roof Rail Weatherstrip
p/n: 14-0038-67
Seal, quarter post to folding top, good copy of original. Four (4) piece set. Length: 11.625 inches.
Side Roof Rail Weatherstrip
p/n: 70-0081-67
High-quality dense rubber seal, for a variety of uses. Available by the foot.
Side Window Header Channel
p/n: 70-0306-58
Plush lined rubber channel for across top of doors above side windows on closed bodies. Available by the foot.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Sidemount Wheel Carrier Grommet
p/n: 60-0002-37
This Sidemount Wheel Carrier Grommet for the wheel carrier brace support-at-cowl panel. Manufactured with a heavy brass core. Has a flexible neck. A close copy of original.