Search Results
Please click on the part name in red in order to get a complete description.
Motor Mount
p/n: 70-0300-11
Motor mount. Intermediate motor mount for support bolts. Split in half if needed at installation. Four (4) piece set.
Motor Mount
p/n: 70-0442-11
Rear motor mount support pad at transmission. Four (4) piece set after splitting. V-8 and V-12
Hood hinge top strap pivot
p/n: 70-0045-42
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Ferrule installing tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Hinge Pillar Weatherstrip
p/n: 70-0734-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Rigid run channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.Length: 16.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Front apron crossbar grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Side mount spare grommet kit
p/n: 70-1134-37
Grommet set, spare wheel fender mount, for various applications to support arms, brace rods and cowl standoff posts. Six (6) piece set.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Shock and stabilizer seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.Width: 1.1875 inches.
Hood ventilator bumper kit
p/n: 70-0011-42
Pad set, hood vent door open limit. Set of twenty (20) pads for one (1) hood, including split rivets for installing.
Cadillac V-8 pedal pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Radiator brace filler strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Cowl vent gasket
p/n: 70-0713-54
Gasket, cowl side ventilator. One eighth (1/8) inch sponge rubber.Length: 11.375 inches. Width: 4.625 inches.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Taillight gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base.Width: 3.25 inches.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This golf bag door weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Body mounting pad
p/n: 70-0297-48
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Rumbleseat lid corner pad
p/n: 70-0120-87
Pad, rumbleseat lid corner, Compare with our #60-0191-87.Length: .75 inches.
Bowdrill cloth tape
p/n: 70-1175-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Body bolt cushion
p/n: 70-0265-48
Cushion for body bolts, for use in metal cups. Fully molded rubber. One and one half inch (1 1/2") outside diameter by seven sixteenths inch (7/16') inside hole diameter by one and one fourth inch (1 1/4") height.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Door handle ferrule
p/n: 70-0111-69
Ferrule, for three fourths (3/4) inch outside door handle. Chrome plated brass. (See #70-0009-69 for grommet). Used for outside door handle or outside trunk handle.
Door bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Side window run channel
p/n: 70-1169-58
Channel, side window, pre-flocked, nine sixteenths (9/16) inch wide to accommodate metal frame side window.
Door Bumper
p/n: 70-1156-71
Pad, door side bumper. Clip retained. Appears identical to Atwood #107, #208.Width: 1.5 inches. Height: 1.3125 inches.
Fabric hood lacing
p/n: 70-2221-42
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Fabric hood lacing
p/n: 60-0578-42
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Door bumper
p/n: 34-0025-42
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Body mounting pad
p/n: 70-0264-48
Cushion, body bolts under washer below bracket. Fully molded rubber. One and one half inch (1 1/2") inch outside diameter by seventeen thirty seconds inch (17/32") inside hole diameter by one fourth inch (1/4") height.
Side window roller
p/n: 70-0117-62
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Side roof rail weatherstrip
p/n: 70-0060-65
Weatherstrip, side roof rail. Made from dense rubber extrusion.Width: 1.0 inches. Height: .6875 inches.
Door handle grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Universal Mounting Pad
p/n: 70-0019-52
Pad, universal mounting, two and one eighths (2-1/8) inches wide. Heavy rubbery pad with half round (3/16) inch bead for windshield frame mounting to cowl on open cars. Black rubber.
Side roof rail weatherstrip
p/n: 70-0081-67
Weatherstrip, side window.Length: 1.4375 inches. Width: .625 inches.
Door check link rod end stop
p/n: 70-0325-70
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Channel filler weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel.Width: .375 inches. Height: .
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall grommet
p/n: 32-0134-20
Special grommet with wide spacing for frame metal to pass electrical wiring and cables through frame. Sheet Metal Hole: 1-1/16" Center Hole: 13/16" Outside Diameter: 1-5/16" Slot Width: 5/32"
Fuel line grommet
p/n: 32-0714-41
Grommet, fuel line and other uses through firewall. Sheet Metal Hole: 1" Center Hole: 3/8" Outside Diameter: 1-5/16" Slot Width: 1/16"
Hood corner pad
p/n: 34-1186-42
Pads, hood door corners, cup type.1931 Twenty (20) required. 1932 Twenty Four (24) required.Height: .375 inches.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Filler and cushion strip
p/n: 70-1237-48
Filler and cushion strip, many applications. Five thirty seconds (5/32) inch by one and five eighths (1-5/8) inch.
Filler and cushion strip
p/n: 70-1236-48
Filler and cushion strip, many applications. One sixteenth (1/16) inch by one and three eighths (1-3/8) inch.
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Firewall grommet
p/n: 32-0133-21
Special grommet with wide spacing for frame metal, to pass electrical wiring and cables through frame. Sheet Metal Hole: 31/32" Center Hole: 3/4" Outside Diameter: 1-3/16" Slot Width: 3/16"
Side window weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge, retained in metal flap on side of carrier channel, seals out water when window is cranked up.Width: .375 inches.
Convertible rail grommet
p/n: 32-0132-67
Grommet, upper side rail, for styles with removable rails. Sheet Metal Hole: 1/2" Center Hole: 3/8" Outside Diameter: 13/16" Slot Width: 3/32"