Front Door Vent Window Weatherstrips
p/n: 38-0044-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Fuel Neck Grommet
p/n: 60-0405-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and eleven sixteenths inch (3-11/16") outside width by four and one fourth (4-1/4") outside length. Two and one fourth inch (2-1/4") inside hole diameter by one half inch (1/2") height.
Handbrake Lever Anti-Rattle
p/n: 60-0531-24
Spacer, anti-rattle, handbrake lever sector rod, between release rod and handbrake lever.Width: .6875 inches. Height: .6875 inches.
Headlight Mounting Pad
p/n: 60-0557-14
Pad, headlight bracket to radiator shell. Round, with proper type weatherlip as original. Two (2) required per vehicle.
Headlight Mounting Pad
p/n: 60-0558-14
Pad, headlight bracket at fender. See also our #60-0178-14. Two and one eighth (2-1/8) inch by three and seven sixteenths (3-7/16) inch.Length: 3.
Headlight Mounting Pad
p/n: 60-0178-14
Pads, headlight bracket mounting. Two (2) inch by three and five eighths (3-5/8) inch overall.Length: 3.625 inches. Width: 2.0 inches.
Hood Corner Pad
p/n: 60-0042-42
Pads, hood corners, right and left. Four (4) piece set.Width: 1.125 inches. Height: 1.125 inches.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Weatherstrip
p/n: 60-0446-77
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Rear Bumper Grommet
p/n: 60-0406-28
Grommets, rear bumper. Right and left sides. Left side has clearance for tail light wire.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear Window Gasket
p/n: 60-0367-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Steering Column Cushion
p/n: 60-0012-36
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Transmission Mount Service
p/n: 60-0504-25
Insulator support, frame to free wheeling unit. Revulcanization service only.
Trunk Hinge Mounting Pad
p/n: 60-0604-87
Pads, trunk hinge. 6 (six) piece set sold in complete sets only.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent division bar weatherstrip
p/n: 60-0626-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.