Please click on the part name in red in order to get a complete description.
Bumper, door glass. Installs in hole on door.
Washer, front fender. Small type. One and one fourth (1-1/4) inch diameter.
Washer, rear fender. Large type. One and one half (1-1/2) inch diameter.
Bumper, door glass. Installs in hole on garnish molding.
Bumper, door check arm.
Gasket, license plate light lens.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Grommet, dash. Black.
Bumper, standard. See detail page for specific usage.
Grommet, wiring harness through fender skirts, or hood latch lower mounting panels. Also other miscellaneous uses. Sheet Metal Hole: 1-1/16" Center Hole: 3/4" Outside Diameter: 1-3/8" Slot Width: 1/16"
Bumper, trunk or hood. Molded with clearance for screw. Used for: Buick 1942-50 Bumper for trunk. Chevrolet 1949-55 Bumper for rear hood corners on cowl. Chevrolet 1949-50 Bumper for trunk. Oldsmobile 1938 Bumper under hood corner on radi
Bushing, for double acting shock absorber arm link. Height: .78125 inches.
Grommet, Bijur Lubricator delivery tube thru frame at various places. Use as required, up to eight (8) per car. Sheet Metal Hole: 3/8" Center Hole: 5/32" Outside Diameter: 9/16" Slot Width: 5/32"
Cushion, wheel shield. Five (5) to six (6) pieces per wheel.Length: 1.0625 inches. Width: .50 inches. Height: .4375 inches.
Seal, lower side window. Fastens to inner face of door to seal against outer side of glass. Also used as weatherstrip on crank-up windshield tops.
Weatherstrip, side window lower edge, retained in metal flap on side of carrier channel, seals out water when window is cranked up.Width: .375 inches.
Grommet, electric wire through body for head and taillights. Sheet Metal Hole: 11/16" Center Hole: 3/8" Outside Diameter: 1" Slot Width: 1/16"
Weatherstrip, windshield, largest type of T-rubber, one and one half (1-1/2) inch high.
Weatherstrip, windshield, T-rubber, short style. Seven sixteenths (7/16) inch high.Height: .4375 inches.
Pads, radiator to frame.
Grommet, license light wire through body. Sheet Metal Hole: 3/4" Center Hole: 5/16" Outside Diameter: 1" Slot Width: 1/16"
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Grommet, sidemount upper. Sheet Metal Hole: 7/8" Center Hole: 1/2" Outside Diameter: 1-5/16" Slot Width: 1/16"
Filler and cushion strip, many applications. One sixteenth (1/16) inch by one and three eighths (1-3/8) inch.
Grommet, sidemount upper brace through cowl. Sheet Metal Hole: 1-1/4" Center Hole: 3/4" Outside Diameter: 1-5/8" Slot Width: 1/16"
Bumper, window glass cushion. One (1) required per door.
Filler and cushion strip, many applications. Five thirty seconds (5/32) inch by one and five eighths (1-5/8) inch.
Grommet, clutch release bearing grease tube through side of bell housing. Sheet Metal Hole: 3/4" Center Hole: 3/8" Outside Diameter: 1" Slot Width: 3/16"
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Pads, outside door handle. Paper type.
Bumpers, door jam. Two (2) required per door.
Pads, outside door handle. Paper type.
Clip, end of door window run channel. Tempered spring steel. Length: 1.8125 inches. Width: .50 inches.
Washer, front upper motor mount. Mount rests in between. Two (2) per truck.
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose.
Grommet, for wiring through front body brace, right and left. Sheet Metal Hole: 1" Center Hole: 7/16" Outside Diameter: 1-7/16" Slot Width: 1/16"
Grommet, brake cable support. Fits in bracket on outside of frame. Sheet Metal Hole: 7/8" Center Hole: 5/16" Outside Diameter: 1-1/4" Slot Width: 1/8"
Side window weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Weatherstrip, side window, (possibly used on other coachwork). Exact copy of original, top quality, fine detail. Murphy-bodied Duesenberg Convertibles.
Weatherstrip, windshield specially marked for trimming to accommodate both widths required (1" or 1-1/2"), sold as one and one half (1-1/2) inch width only.
Filler, for glass channel for convertible type windows with metal frame around one fourth (1/4) inch glass.Width: .4375 inches. Height: .50 inches.
Weatherstrip, window, for models with lip for attaching bead molding.
Weatherstrip, side roof rail. Three fourths inches (3/4") wide. Fits into metal channel retainer. See our #70-1172-65 and #70-1173-65 for cloth covering. Note: Order twelve feet (12') for two (2) door models, fourteen feet (14') for four (4) door
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel.Width: .375 inches. Height: .
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Grommets, headlight wire conduit through radiator shell. Sheet Metal Hole: 1-5/16" Center Hole: 1/2" Outside Diameter: 1-5/8" Slot Width: 1/16"
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Bushing, shock absorber arm link.
Anti-rub cover, brake cable. Fits all models with seven sixteenths (7/16) inch outside diameter cable.Width: 2.0 inches.
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Weatherstrip, side window. Base fifteen sixteenths (15/16) inch wide but easily trims to more narrow channel if necessary.Width: .9375 inches.
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Weatherstrip, side window, rubber only. Fits in metal retainer as shown.Width: 1.0625 inches. Height: .50 inches.
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Weatherstrip, side window.Ford Cars 1931-39 Weatherstrip, side window, certain Lincoln K-models with Coachmaker bodies.
Bumper, special garnish molding. Five (5) inches long.
Bumper, door jam.
Seal, wiper motor shaft to roof. Replaces factory #40-17541.
Gasket, taillight lens. Inner and outer seal. Enough for one taillight lens.
Pad, trunk lid handle.
Grommet, battery cable through frame.
Seal or cover, leaf spring eye or shackle bolt end.
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Grommets, firewall, for ignition cable and temperature gauge. Two (2) required per car. Sheet Metal Hole: 1-3/8" Center Hole: 7/16" Outside Diameter: 1-3/4" Slot Width: 3/32"
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Cushion, body bolts under washer below bracket. Fully molded rubber. One and one half inch (1 1/2") inch outside diameter by seventeen thirty seconds inch (17/32") inside hole diameter by one fourth inch (1/4") height.
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Rubber washer, door check link stop.
Spacer, anti-rattle, handbrake lever sector rod, between release rod and handbrake lever.Width: .6875 inches. Height: .6875 inches.
Mounting pad. Two and one fourth (2-1/4) inches outside diameter by five eighths (5/8) inch inside diameter by one half (1/2) inch thick.
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Pad, side window lower rest. Two (2) per window.
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Grommet, rear spare wheel carrier mounting bracket. Sheet Metal Hole: 1-1/16" Center Hole: 5/8" Outside Diameter: 2-1/16" Slot Width: 3/32"
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Bolt, front or rear motor mount.Ford Truck 1932-51 Bolt, front motor mount. 2 per truck except as noted.
Bumpers, trunk or rumble seat lid. Upper.
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Seals, wind-wing bracket rubber. Holds glass in place. Four (4) piece set. Replaces factory #B-7603108.
Pad, door side bumper. Clip retained.
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Pad, door side bumper. Clip retained. Appears identical to Atwood #107, #208.Width: 1.5 inches. Height: 1.3125 inches.
Channel, side window, pre-flocked, nine sixteenths (9/16) inch wide to accommodate metal frame side window.
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Channel, side window, pre-flocked, five sixteenths (5/16) inch wide base for one fourth (1/4) inch glass. Most Fisher closed bodies except those using stainless beaded channel. For nine sixteenths (9/16) inch wide channel, see our #70-1169-58.
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Gasket, headlight bucket to lens.
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Pads, outside door handle.
Pad, transmission support (lower).
Grommet, cowl wiring firewall.
Pads, outside door handle.