This Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, front bow-to-windshield, soft rubber, hollow body, proper screw holes, hinged flaps front and back.
Grommets, rear bumper, hollow construction, superb copy, three and one half (3-1/2) inch high. Similar to our #50-0086-29.Length: 4.25 inches.
Mounting pad, windshield frame to cowl. Molded in two (2) parts with joint in center. Canvas base as original.Length: 48.0 inches.
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Grommet, rear bumper. Fully molded rubber. Four and one fourths inch (4-1/4") outside length by two and three eighths inch (2-3/8") outside width. Three inches (3") inside hole length by one and one eighths inch (1-1/8") inside hole width by two and one h
Floorplate at steering column and pedals. Brown rubber. Metal core as original.
Floorplate at steering column and pedals. Black rubber. For brown see our #50-0117-89. Metal core as original.Width: 9.25 inches.
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Grommet set, side mounted spare wheel brace. Four (4) piece set with two (2) different sizes.
Pad, hood corners, rear. Molded left and right with metal core.Width: 1.625 inches. Height: 1.375 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Pads, brake and clutch pedals. Black rubber. For brown see our #50-0077-89. Two and three fourth (2-3/4) inches by three and three eighths (3-3/8) inches.
Headlight mount pads. Non symmetrical. Replaces #1285200-1, for 3-1/4" X 6-1/4" base. Excellent copy.
Pads, brake and clutch pedals. Brown rubber. For black see our #50-0077-22. Two and three fourth (2-3/4) inches by three and three eighths (3-3/8) inches.
Accelerator pedal pad manufactured in Brown rubber. Full slip-over type and a perfect copy.
Pads, hood corner, front.
Grommet, fuel filler neck. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2-3/16") inside diameter by three fourths inch (3/4") height.
Accelerator pedal pad manufactured in Black rubber. Full slip-over type and a perfect copy. For Brown see our #50-0080-89.
Taillight mounting pad. Excellent copy with proper lip at edge. Replaces #1273863. Customer must cut holes for wires, bulb, screws etc as required.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Grommet, horn mounting bracket.Width: 2.125 inches.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Pad, rumbleseat step mounting for fender, double beaded edge per original.Width: 4.375 inches.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Gasket, cowl vent cover.Width: 18.25 inches. Height: 4.0 inches.
Boot, starter solenoid.
Gasket, windshield wiper transmission.Width: 2.5625 inches. Height: .8125 inches.
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Bowdrill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Ferrule, for three fourths (3/4) inch outside door handle. Chrome plated brass. (See #70-0009-69 for grommet). Used for outside door handle or outside trunk handle.
This Vent Window Division Bar Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Bowdrill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Pad, transmission support (lower).
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Pad, door side bumper. Clip retained.
This Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
This Fabric Hood Lacing is made of a high quality original style woven cotton. Available by the foot to accommodate any job.
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Rubber washer, door check link stop.