Search Results
Please click on the part name in red in order to get a complete description.
Runningboard matting
p/n: 30-0214-49
Runningboard matting. Fully molded right and left hand. Top quality rubber, flawless detail. Includes rubber cross molding for in front of rear fender.
Motor mount service
p/n: 30-0365-11
Support assembly, rear of engine right and left. Revulcanization service only.
Suspension bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Front suspension bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Front Door Vent Window Weatherstrips
p/n: 30-0053-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Rear Window Gasket
p/n: 30-0522-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Transmission stabilizer
p/n: 30-0252-24
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Axle rebound pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Axle rebound pad
p/n: 30-0043-32
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
Rear bumper grommet
p/n: 30-0159-29
Grommets, rear bumper. Molded right and left as original.Length: 4.875 inches. Width: 3.125 inches.
Swing-out Windshield Weatherstrip
p/n: 70-0057-52
This swing-out windshield weatherstrip comes in an twelve foot (12') strip and mounts into the metal channel attached to the glass. The rubber slides into the T-groove and creates a seal when the glass is pressed against the body of the vehicle.
Front bumper grommet
p/n: 30-0077-28
Grommets, front bumper. Molded right and left, including retaining flange. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside length by two and five eighths inch (2-5/8") outside width by one and one half inch (1-1/2") inside hole l
Accelerator pedal service
p/n: 30-0400-41
Pedal, accelerator. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.Length: 9.625 inches.
Side mount tire cushion
p/n: 30-0410-37
Cushion, upper (thin) spare wheel in fender well. Two (2) per car.Length: 11.25 inches. Width: 3.0 inches.
Rear bumper grommet
p/n: 30-0047-29
Grommets, rear bumper. For models with luggage racks.Length: 4.125 inches. Width: 3.375 inches.
Motor mount pad
p/n: 30-0238-11
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Rear Window Gasket Weatherstrip
p/n: 30-0086-83
This rear window gasket weatherstrip comes in a seven foot (7') strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Side mount tire cushion
p/n: 30-0411-37
Cushion, lower (thick) spare wheel in fender well. Two (2) per car.Length: 11.0 inches. Width: 3.0 inches.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Taillight mounting pad
p/n: 30-0230-15
Gaskets, taillight mounting. Proper type lip as original. One and eleven sixteenths (1-11/16) inch by four and one half (4-1/4) inch.Length: 4.25 inches.
Brake and clutch pedal pad
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Fuel neck grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Radiator mounting pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Brake cable anti-rub cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Side mount grommet
p/n: 30-0100-37
Grommets, spare wheel sidemount brace, lower.Length: 2.625 inches. Width: 2.50 inches.
Cowl vent gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Flexible Run Channel
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Five eights (5/8) inch wide, six (6) foot long. Cloth covered mohair-lined type. For sides and top of side windows. High quality, perfect copy. Applications without vent window use a six (6) foot strip. Application
Flexible Run Channel 6 Foot
p/n: 70-1239-58
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Brake and clutch shank seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Flexible Run Channel 5 Foot
p/n: 70-1238-58
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Flexible Run Channel
p/n: 70-1107-57
Channel, flexible window run, un-beaded. Five eighths (5/8) inch wide, five (5) foot long. Cloth covered mohair-lined type. For sides and top of side windows. High quality, perfect copy. Applications with vent window use a five (5) ft. strip. Applications
Trunk lid clamp mounting pad
p/n: 30-0182-87
Pads, trunk lid hasp (clamp) mounting. Fine beaded edge, perfect copy. These are not hinge pads. Four (4) piece set.Length: 4.0 inches. Width: 1.0 inches.
Brake and clutch pedal bumper
p/n: 30-0380-20
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Taillight lens gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door bumper
p/n: 30-0052-71
Bumper, door side, upper. Oblong type, perfect copy of original.Length: 2.4375 inches.
Door bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Door bumper
p/n: 30-0032-71
Pad, for door. Circular shape, one and one fourth (1-1/4) inch diameter.
Stabilizer grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car. One and one fourth inch (1 1/4") outside diameter by one half inch (1/2") inside hole diameter by seven eighths inch (7/8") height. Used as a f
Shock and stabilizer bushing
p/n: 50-0220-32
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Door and trunk handle gasket
p/n: 30-0235-71
Pad, outside door handle escutcheon.Length: 2.4375 inches.
Shock absorber bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Trunk Weatherstrip
p/n: 50-0161-85
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Shock and stabilizer grommet
p/n: 70-0274-33
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Bijur lubricator spring seal
p/n: 30-0434-32
Seal, spring shackle. For models with Bijur lubrication systems.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 30-0144-87
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Bijur Lubricator Frame Grommet
p/n: 32-0414-32
Grommet, Bijur Lubricator delivery tube thru frame at various places. Use as required, up to eight (8) per car. Sheet Metal Hole: 3/8" Center Hole: 5/32" Outside Diameter: 9/16" Slot Width: 5/32"
